Poulan 530164603 Service, Limbing and Pruning Important Points, Important Have all

Page 13

Using a log for support

2nd Cut

1st Cut

1st Cut

2nd Cut

Using a support stand

2nd Cut

1st Cut

1st Cut

2nd Cut

LIMBING AND PRUNING

WARNING: Be alert for and guard against kickback. Do not allow the moving chain to contact any other branches or objects at the nose of the guide bar when limbing or pruning. Allowing such contact can result in serious injury.

WARNING: Never climb into a tree to limb or prune. Do not stand on ladders, plat- forms, a log, or in any position which can cause you to lose your balance or control of the saw.

IMPORTANT POINTS

S Work slowly, keeping both hands firmly gripped on the saw. Maintain secure footing and balance.

SWatch out for springpoles. Springpoles are small size limbs which can catch the saw chain and whip toward you or pull you off bal-

ance. Use extreme caution when cutting small size limbs or slender material.

S Be alert for springback. Watch out for branches that are bent or under pressure. Avoid being struck by the branch or the saw when the tension in the wood fibers is released.

S Keep a clear work area. Frequently clear branches out of the way to avoid tripping over them.

LIMBING

SAlways limb a tree after it is cut down. Only then can limbing be done safely and prop-

erly.

SLeave the larger limbs underneath the felled tree to support the tree as you work.

SStart at the base of the felled tree and work toward the top, cutting branches and limbs. Remove small limbs with one cut.

SKeep the tree between you and the chain. Cut from the side of the tree opposite the

branch you are cutting.

S Remove larger, supporting branches with the cutting techniques described in BUCK-

ING WITHOUT A SUPPORT.

SAlways use an overcut to cut small and free- ly hanging limbs. Undercutting could cause limbs to fall and pinch the saw.

PRUNING

WARNING: Limit pruning to limbs shoulder height or below. Do not cut if branches are higher than your shoulder. Get a professional to do the job.

SMake your first cut 1/3 of the way through the

bottom of the limb.

SNext make a 2nd cut all the way through the limb. Then cut a third overcut leaving a 1 to 2 inch (2.5 to 5 cm) collar from the truck of the tree.

Second cut

Third cut

Collar

First cut

Pruning technique

SERVICE

WARNING: Disconnect the spark plug before performing maintenance except for carburetor adjustments.

We recommend all service and adjustments not listed in this manual be performed by an authorized or Master Service Dealer.

HELPFUL TIP

IMPORTANT: Have all

repairs other than the rec- ommended maintenance described in the instruction manual performed by an authorized service dealer.

If any dealer other than an authorized service dealer performs work on the product, Electrolux Home Products, Inc., may not pay for repairs under war- ranty. It is your responsibility to maintain and perform general maintenance.

13

Image 13
Contents 530164603 English Español Français16/04 Safety Rules Identification of SymbolsPlan Ahead Maintain Your SAW in Good Working Order Operate Your SAW SafelyHandle Fuel with Caution KickbackReduce the Chance of Kickback Kickback Safety FeaturesMaintain Control 1950/1975 952044368 Chain Brake and CKA Angle952051209 2050/2050WT 2055/2075 952044370 952051211 2150/2150PR 2155/2175 952044418Inside view Chain Brake Adjustment located on Chain Brake AssemblyAttaching the BAR & Chain If not Chain Brake NutsChecking the tension Adjusting the tensionChain Tension Know Your Chain SAW ON/STOP SwitchThrottle Trigger Throttle LOCK-OUTFueling Engine StartingBAR and Chain Lubrication Important Points to RememberStarting a Warm Engine Cutting MethodsImportant Points Felling Large Trees Tree Felling TechniquesNotch CUT and Felling the Tree Direction of FallCutting a Fallen Tree Bucking Using a LOG or Support StandTypes of Cutting Used for Bucking Bucking Without a SupportLimbing and Pruning Important Points ServiceLimbing PruningCarburetor Adjustment Cleaning the Spark ARREST- ING ScreenAIR Filter Inspect Muffler and Spark Arresting ScreenNeed ASSISTANCE? Load Adjustment Engine Limited WarrantyEmpty fuel tank and refill with Ligations The U. S. Environmental NANCE, Replacement and Repair of Emission Related Parts AnyElectrolux Home PRODUCTS, INC Intermediate 125 hours Extended 300 hours