KNOW YOUR SAW
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR CHAIN SAW. Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual for future refer- ence.
|
|
|
| Bar Oil Cap |
|
|
|
|
|
|
| Hand Guard | |||||||||||
Trigger Lockout |
|
|
|
|
|
|
|
|
|
|
|
|
|
| Chain Adjustment Screw | ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||
Button |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
Power |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
Cord |
|
|
|
|
|
|
| Trigger Switch |
|
| Bar Clamp | Bar |
| Chain | |||||||||
|
|
|
|
|
|
|
|
|
| ||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||
TRIGGER SWITCH |
|
|
|
|
|
|
| BAR OIL CAP |
|
|
|
|
| ||||||||||
The TRIGGER SWITCH is used to turn on | The BAR OIL CAP is used to fill the bar oil | ||||||||||
the unit. Squeeze the trigger switch to | tank. | ||||||||||
operate the unit after | CHAIN ADJUSTMENT SCREW | ||||||||||
has been pushed forward. Release the | The CHAIN ADJUSTMENT SCREW is | ||||||||||
trigger to turn the unit off. | used to adjust the chain tension. | ||||||||||
TRIGGER | POWER CORD | ||||||||||
The TRIGGER | The POWER CORD is used to connect | ||||||||||
control feature designed to prevent the | the chain saw to an approved extension | ||||||||||
motor from being accidently started. | cord. | ||||||||||
When the rear handle is gripped in a nor- | CHAIN TENSION | ||||||||||
mal cutting position, the | It is normal for a new chain to stretch dur- | ||||||||||
can be pushed in by the thumb, permit- | ing first 30 minutes of operation. You | ||||||||||
ting the index finger to squeeze the trig- | should check your chain tension frequent- | ||||||||||
ger. It is not necessary to maintain pres- | ly. See CHAIN TENSION under the SER- | ||||||||||
sure on the | VICE AND ADJUSTMENTS section. | ||||||||||
trigger has been engaged. |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| |
OPERATING INSTRUCTIONS | Power Cord | ||||||||||
Use only a voltage supply as specified on | |||||||||||
|
|
|
|
|
|
|
|
|
| ||
your unit. |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| ||
SELECT AN EXTENSION CORD |
|
|
|
|
|
|
|
|
|
| |
Extension cords are available for this unit . |
|
|
|
|
|
|
|
|
|
| |
MINIMUM WIRE GAUGE
RECOMMENDATIONS
Volts | 25 ft. | 50 ft. | 100 ft. | ||
(7.67 | M) | (15.24 M) | (30.48 M) | ||
| |||||
120 | 16 |
| 16 | 14 | |
A.W.G.* | A.W.G.* | A.W.G.* | |||
| |||||
|
|
|
|
| |
*American Wire Gauge
ATTACH THE EXTENSION CORD TO YOUR CHAIN SAW
To prevent disconnection from unit, se- cure extension cord to power cord as shown in the following illustration.
Extension Cord
BEFORE STARTING SAW
WARNING: Be sure to read the electrical safety information in the safety rules section of this manual before you begin. If you do not understand the elec- trical safety information do not attempt to use your unit. Seek help from someone that does understand the information or call the customer assistance help line at
7