Poulan 530164293 Reduce the Chance of Kickback, Maintain Control, Kickback Safety Features

Page 4

Avoid Obstructions

Clear The Working Area

REDUCE THE CHANCE OF KICKBACK

S Recognize that kickback can happen. With a basic understanding of kickback, you can reduce the element of surprise which contributes to accidents.

SNever let the moving chain contact any ob- ject at the tip of the guide bar.

SKeep the working area free from obstruc- tions such as other trees, branches, rocks, fences, stumps, etc. Eliminate or avoid any obstruction that your saw chain could hit while you are cutting. When cutting a

branch, do not let the guide bar contact branch or other objects around it.

SKeep your saw chain sharp and properly tensioned. A loose or dull chain can in- crease the chance of kickback occurring. Follow manufacturer’s chain sharpening and maintenance instructions. Check ten- sion at regular intervals with the engine stopped, never with the engine running.

Make sure the bar nuts are securely tight- ened after tensioning the chain.

SBegin and continue cutting at full speed. If the chain is moving at a slower speed, there is greater chance of kickback occur-

ring.

SCut one log at a time.

SUse extreme caution when re-entering a

previous cut.

SDo not attempt cuts starting with the tip of

the bar (plunge cuts).

SWatch for shifting logs or other forces that could close a cut and pinch or fall into

chain.

SUse the Reduced--Kickback Guide Bar and Low--Kickback Chain specified for your saw.

MAINTAIN CONTROL

Stand to the left of the saw

Thumb on underside of handlebar

Never reverse hand positions

Elbow locked

Thumb on underside of handlebar

SKeep a good, firm grip on the saw with both hands when the engine is running and don’t let go. A firm grip will help you reduce kickback and maintain control of the saw. Keep the fingers of your left hand encir- cling and your left thumb under the front handlebar. Keep your right hand com- pletely around the rear handle whether your are right handed or left handed. Keep

your left arm straight with the elbow locked.

SPosition your left hand on the front handle- bar so it is in a straight line with your right hand on the rear handle when making bucking cuts. Never reverse right and left

hand positions for any type of cutting.

SStand with your weight evenly balanced on

both feet.

SStand slightly to the left side of the saw to keep your body from being in a direct line with the cutting chain.

SDo not overreach. You could be drawn or

thrown off balance and lose control of the saw.

SDo not cut above shoulder height. It is diffi- cult to maintain control of saw above shoulder height.

KICKBACK SAFETY FEATURES

WARNING: The following features are included on your saw to help reduce the hazard of kickback; however, such features will not totally eliminate this danger. As a chain saw user, do not rely only on safety de- vices. You must follow all safety precau- tions, instructions, and maintenance in this manual to help avoid kickback and other forces which can result in serious injury.

SReduced--Kickback Guide Bar, designed with a small radius tip which reduces the size of the kickback danger zone on the bar tip. A Reduced--Kickback Guide Bar has been demonstrated to significantly re- duce the number and seriousness of kick- backs when tested in accordance with safety requirements for gasoline powered

chain saws as set by ANSI B175.1.

Reduced Kickback Symmetrical Guide Bar

Small Radius Tip

4

Image 4
Contents 530164293 16/04Identification of Symbols Plan AheadOperate Your SAW Safely Maintain Your SAW in Good Working OrderHandle Fuel with Caution KickbackReduce the Chance of Kickback Kickback Safety FeaturesMaintain Control Chain Brake and CKA Angle WE do not REPResent and YOU should not AS Sume That the Chain Brake willAssembly Attaching the BAR & Chain If notAdjusting the tension Adjusting ScrewChain Tension Checking the tensionOperation BAR and Chain Lubrication Before Starting Engine Fueling EngineImportant Points to Remember Starting a Warm Engine Difficult Starting or starting a flooded engineBraking function control Caution The chain brake must be Inertia activating function controlTension in the Assembly section Operating TipsTree Felling Techniques Felling Large TreesBucking Using a LOG or Support Stand Cutting a Fallen TreeImportant Points Types of Cutting Used for BuckingLimbing and Pruning Important Points LimbingPruning ING Without a SupportService Inspect and Clean Unit and Decals Clean AIR FilterCleaning the Spark ARREST- ING Screen Check Fuel Mixture LevelStorage Load Adjustment Engine EngineOther Empty fuel tank and refill withLigations The U. S. Environmental Electrolux Home PRODUCTS, INCNANCE, Replacement and Repair of Emission Related Parts Any