Poulan 530163152 Know Your Chain SAW, ON/STOP Switch, Throttle Trigger, Throttle LOCK-OUT

Page 8

KNOW YOUR CHAIN SAW

READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR CHAIN SAW. Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference.

Chain

Front Hand Guard

Front Handle

Adjustment Tool

 

Starter Rope

(Bar Tool)

 

 

ON/STOP

 

 

 

 

Switch

Chain

Muffler

 

 

 

Primer

 

 

 

 

 

 

Bulb

 

 

Bar Oil Fill Cap

Starter

 

 

 

 

 

Housing

Fuel Mix Fill Cap

 

Cylinder Cover

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fast Idle

 

 

 

 

 

 

 

 

Throttle Lock

 

 

 

 

 

 

 

 

Chain

 

 

 

 

 

 

 

 

Lockout

 

 

 

 

 

 

 

 

 

 

 

Adjusting

 

 

Direction

 

 

 

 

 

 

 

Rear

 

 

 

 

 

 

of Travel

 

 

 

 

Screw

 

 

Handle

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Guide Bar

Throttle

Choke

 

 

 

 

 

Chain Brake

Bar

Chain

Chain

Nuts

Sprocket

Trigger

Knob

 

 

Brake

Catcher

 

Hole

ON/STOP SWITCH

The ON/STOP SWITCH is used to stop the engine.

THROTTLE TRIGGER

The THROTTLE TRIGGER controls engine speed.

THROTTLE LOCK-OUT

The THROTTLE LOCK--OUT must be pressed before you can squeeze the throttle trigger. This feature prevents you from acci- dentally squeezing the trigger.

FAST IDLE LOCK

The FAST IDLE LOCK holds the throttle trigger in the starting position. Activate the fast idle lock by pressing the throttle lockout and squeezing the throttle trigger. With the throttle trigger squeezed, press the fast idle lock. Re- lease the throttle lockout and trigger while hold- ing the fast idle lock button.

CHOKE KNOB

The CHOKE KNOB activates the choke to provide additional fuel to the engine during cold starting.

PRIMER BULB

The PRIMER BULB circulates fuel to the car- buretor to provide quicker starting.

CHAIN BRAKE

The CHAIN BRAKE is a device designed to stop the chain if kickback occurs. The chain brake activates automatically in the event of kickback. The chain brake activates manually if the front hand guard is pushed forward. The chain brake is disengaged by pulling the front hand guard back toward the front handle as far as possible.

CHAIN TENSION

It is normal for a new chain to stretch during first 30 minutes of operation. You should check your chain tension frequently. See CHAIN TENSION under the ASSEMBLY section.

WARNING: Muffler is very hot dur- ing and after use. Do not touch the muffler or allow combustible material such as dry grass or fuel to do so.

8

Image 8
Contents Manual de Instrucciones Manuel d’Instructions Plan Ahead Operate Your SAW Safely Maintain Your SAW in Good Working OrderHandle Fuel with Caution KickbackKickback Safety Features Reduce the Chance KickbackMaintain Control Avoid Obstructions Clear The Working AreaChain Brake and CKA Angle Resent and YOU should not ASSume That the Chain Brake will Protect YOU in the Event of a KickInside view Chain Brake Adjustment located on Chain Brake Attaching the BAR & Chain If notChain Tension Adjusting the tensionChecking the tension ON/STOP Switch Know Your Chain SAWThrottle Trigger Throttle LOCK-OUTImportant Points to Remember Fueling EngineBAR and Chain Lubrication Starting a Warm Engine Difficult Starting or starting a flooded engineBraking function control Caution The chain brake must be Inertia activating function controlTree Felling Techniques Felling Large Trees Notch CUT and Felling the TreeBucking Using a LOG or Support Stand Cutting a Fallen TreeTypes of Cutting Used for Bucking Bucking Without a SupportCleaning the air filter Limbing and Pruning Important PointsLimbing PruningCleaning the Spark ARREST- ING Screen Carburetor AdjustmentsBAR Maintenance Inspect Muffler and Spark Arresting ScreenNeed Service PART? Chain SharpeningIgnition Timing Spark PlugTroubleshooting Table Cause Remedy Your Warranty Rights and OB Ligations The U.S. Environmental