Poulan 2001-07 Know Your SAW, ON/STOP Switch, Throttle Trigger, Throttle Lockout, Primer Bulb

Page 8

KNOW YOUR SAW

READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR CHAIN SAW. Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference.

Chain

Front Hand Guard

 

 

Front Handle

Adjustment Tool

 

 

 

 

 

 

 

 

 

 

(Bar Tool)

 

 

 

 

 

 

Starter Rope

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ON/STOP

 

 

 

 

 

 

 

Switch

Chain

Muffler

 

 

 

 

 

 

 

Primer

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Bulb

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Bar Oil Fill Cap Starter

Housing Fuel Mix Fill Cap

Cylinder Cover

 

Throttle

 

Chain

Rear

Lockout

Adjusting

Direction

 

Screw

of Travel

Handle

 

 

 

Throttle

Choke/

Chain

Chain

Chain Brake Nuts

Guide Bar

Trigger

Fast Idle

 

 

 

Lever

Brake

Catcher

 

 

 

 

 

 

 

ON/STOP SWITCH

The ON/STOP SWITCH is used to stop the engine.

THROTTLE TRIGGER

The THROTTLE TRIGGER controls engine speed.

THROTTLE LOCKOUT

The THROTTLE LOCKOUT must be pressed before you can squeeze the throttle trigger. This feature prevents you from accidentally squeezing the trigger.

CHOKE/FAST IDLE LEVER

The choke and fast idle are set by pulling the CHOKE/FAST IDLE LEVER out fully for cold or refueled starting. The choke provides addi- tional fuel to the engine during cold starting.

PRIMER BULB

The PRIMER BULB circulates fuel to the carburetor to provide quicker starting.

CHAIN BRAKE

The CHAIN BRAKE is a device designed to stop the chain if kickback occurs. The chain brake activates automatically in the event of kickback. The chain brake activates manu- ally if the front hand guard is pushed forward. The chain brake is disengaged by pulling the front hand guard back toward the front han- dle as far as possible.

CHAIN TENSION

It is normal for a new chain to stretch during first 30 minutes of operation. You should check your chain tension frequently. See CHAIN TENSION under the ASSEMBLY section.

WARNING: Muffler is very hot dur- ing and after use. Do not touch the muffler or allow combustible material such as dry grass or fuel to do so.

8

Image 8
Contents Manual de Instrucciones Manuel d’Instructions Plan Ahead Hearing Afety Hat Protection Eye Snug FittingOperate Your SAW Safely Maintain Your SAW in Good Working OrderHandle Fuel with Caution KickbackKickback Safety Features Reduce the Chance KickbackMaintain Control Avoid Obstructions Clear The Working AreaChain Brake and CKA Angle Computed kickback angle CKA Table Attaching the BAR & Chain If notBAR ModelAdjusting the tension Tip Bar Chain Brake Nuts Chain AdjustmentChecking the tension Fit chain drive links in to bar grooveON/STOP Switch Know Your SAWThrottle Trigger Throttle LockoutImportant Points to Remember Fueling EngineBAR and Chain Lubrication Starting a Warm Engine Difficult Starting or starting a flooded engineInertia activating function control Important PointsTree Felling Techniques Felling Large TreesNotch CUT and Felling the Tree Plan a clear retreat pathBucking Using a LOG or Support Stand Cutting a Fallen TreeTypes of Cutting Used for Bucking Bucking Without a SupportUsing a support stand Limbing and Pruning Important PointsLimbing PruningCleaning the air filter Carburetor AdjustmentsBAR Maintenance AIR FilterNeed Service PART? Troubleshooting Table Cause RemedyChain Sharpening Ignition TimingYour Warranty Rights and OB Ligations The U. S. Environmental