Adjusting the R.A.B.O.S. Equalizer, Position

1.Select a new test position: Cue the test track corresponding to the center frequency of the dip. In the example in Figure 19 you would play Tracks 14 (52Hz) and 18 (40Hz). Press Play ›. You will see a reading very close to what you had before. Now, slowly move the RSLM around the area, if possible remaining within about a foot of the original test point. As you move the RSLM, watch the bar graph. You will observe large level fluctuations. Find a location for the subwoofer or a test location that raises the response at these frequencies. You may find it helpful to move the RSLM vertically. Dips can be oriented in any axis. The position that restores the level to about that of the adjacent test points is your new test position.

2.Reset the test level: Return to the section “Setting the Subwoofer Test Level” on page 7. Perform the procedure as described.

3.Repeat the measurements: Now that you are familiar with the measurement process, you can go much faster by using Tracks 27–50. These tracks contain all the test tones necessary for measurement. However, each test is only about three seconds, and there is no frequency announcement. The first test is 100Hz. Just place each test mark in order until finished. Connect the dots.

Your second measurement will no longer exhibit the deep response dips. However, the peak will still be evident. Without the influence of the response dips, the amplitude and center of the peak may have changed.

4.Interpret the new data: Compare your new data to the examples given in this section of the manual. Follow the instructions for the example that most closely matches your new measurement.

Example 6. Ideal Response:

Figure 20. Ideal response, no EQ needed

If your test data looks similar to the example in Figure 21, you have a very favorable setup. Skip to the “Final System Balance” section, page 15.

Adjusting the R.A.B.O.S. Equalizer

Now that you have performed the measurements and interpreted the data, you have the information needed to adjust the subwoofer’s equalizer.

There are three equalizer adjustments on the subwoofer. Left to right, they are marked Frequency, Level and Width. Each control has 21 positions. These are numbered from left to right. Therefore, Position 1 is the full counterclockwise position. The following table illustrates all switch positions.

Position	F (Hz)	L (dB)	W

1 CCW	20	–14.1	4.5%
2	20	–13.9	5%
3	20	–13.5	7.5%
4	21	–13.1	10%
5	22	–12.7	12.5%
6	24	–11.7	16.5%
7	26	–11.0	20.5%
8	30	–10.2	23%
9	35	–9.5	26%
10	38	–8.9	28%
11	40	–8.3	29.5%
12	43	–7.9	31%
13	46	–6.4	34%
14	49	–4.4	39%
15	52	–2.9	41.5%
16	56	–1.9	43.5%
17	63	–1.1	45%
18	66	–0.5	46.5%
19	72	0.0	48%
20	77	0.0	49%
21 CW	80	0.0	49.5%

CSW-10 14

CSW-10 specifications

The Infinity CSW-10 is a remarkable addition to the realm of high-performance subwoofer systems, designed specifically for those who value superior audio quality in their home theater or music listening environment. This subwoofer integrates technology and craftsmanship to deliver exceptional deep bass, ensuring that it complements a wide range of speaker systems while standing out on its own.

One of the standout features of the CSW-10 is its powerful 10-inch driver. This driver is engineered to produce low-frequency sounds with remarkable clarity and impact. The high excursion capabilities of the driver enable it to move significantly more air, resulting in profound bass reproduction that can be felt throughout the room. Whether you're enjoying an action-packed movie or listening to your favorite music genre, the CSW-10 brings a visceral experience that enhances the audio experience.

The Infinity CSW-10 is equipped with a robust Class D amplifier, which provides ample power while maintaining high efficiency. This amplifier allows the subwoofer to deliver sustained and dynamic performance, ensuring that it can handle everything from subtle sound effects to explosive action sequences. With a total output power rated at 200 watts RMS, the CSW-10 ensures deep, thunderous bass that doesn’t compromise on quality.

In terms of connectivity, the CSW-10 features flexible input options, including both line-level RCA inputs and speaker-level inputs. This versatility makes it easy to integrate the subwoofer into various audio systems, whether they are stereo or surround sound setups. Additionally, the CSW-10 has adjustable volume and phase controls, allowing users to fine-tune the subwoofer's output to match their preferences and room acoustics.

The design of the Infinity CSW-10 is equally impressive. It features a sleek and modern aesthetic that can blend seamlessly into any home decor. The stylish cabinet is constructed from high-quality materials that not only enhance its durability but also minimize unwanted resonance, contributing to the overall sound quality. Furthermore, the subwoofer is equipped with non-skid feet, ensuring stability during intense listening sessions.

Overall, the Infinity CSW-10 represents a perfect fusion of performance, technology, and style. With its powerful driver, efficient amplifier, flexible connectivity, and elegant design, it caters to audio enthusiasts who demand both quality and aesthetics in their sound systems. Whether for music or movies, the CSW-10 is engineered to deliver an immersive auditory experience that truly enhances entertainment.