Tweeter Woofer on kick panel | Infinity Kappa 10.5t specification

INSTALLATION WARNINGS AND TIPS

SPEAKER PLACEMENT

ABOUT THESE INSTRUCTIONS

Installation of automotive stereo components can require extensive experience with a variety of mechanical and electrical procedures. Although these instructions explain how to install Kappa 10.5t tweeters in a general sense, they do not show the exact installation methods for your particular vehicle. If you feel you do not have the experience, do not attempt the installation yourself but, instead, ask your authorized Infinity car audio dealer about professional installation options.

LOUD MUSIC AND HEARING

Playing loud music in an automobile can perma- nently damage your hearing, as well as hinder your ability to hear traffic.The maximum volume levels achievable with Infinity speakers, combined with high power amplification, may exceed safe levels for extended listening. We recommend using low volume levels when driving. Infinity accepts no liability for hearing loss, bodily injury, or property damage as a result of use or misuse of this product.

ABOUT THE CROSSOVER

Passive crossover design involves precise circuit design and component selection. Moreover, a well-designed crossover circuit provides an intended electrical response, when combined with the electrical properties of the speaker, to provide a particular acoustic response. Each enclosed crossover has been optimized to provide a flat response when used with a Kappa 10.5t tweeter.

INSTALLATION TIPS

•Always wear protective eyewear when using any tools.

•Turn off all audio components and other electrical devices before you start. Disconnect the negative (–) lead from your vehicle’s battery.

•Keep speakers in their package until final installation. When moving a speaker, always rest it with the cone or dome facing up. Never use force to install any speaker.

•Check clearances on both sides of a planned mounting surface before drilling any holes or installing any screws. Remember that the screws can extend behind the surface.

•At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when cutting or drilling in and around these areas.

•Before drilling or cutting holes, use a utility knife to remove unwanted fabric or vinyl to keep material from snagging in a drill bit or saw.

•For door installations, check the clearance with the windows throughout the range of the window’s travel, and verify that a mounted speaker will not interfere with the window crank or power-window mechanism.

•If mounting speakers elsewhere, check for clearance around rear-deck torsion bars, glove box or other structural elements.

ABOUT PLACEMENT

Figures 1 and 2 show possible speaker placements with Figure 1 being more desirable. We recom- mend using the kick panel for mounting to obtain the best staging and imaging in most vehicles.

Figure 1. Mounting the woofer and tweeter in the kick panel.

TWEETER and

WOOFER on kick panel

Figure 2. Mounting the woofer in the door and the tweeter in the kick panel.

Do not use another brand or type of passive	• Do not mount speakers where they will get wet.
crossover, or connect more than one tweeter to a
crossover. Doing so may damage the tweeter.

TWEETER on kick panel

WOOFER in factory door location

- 2 -

Kappa 10.5t specifications

The Infinity Kappa 10.5t is a standout product in the realm of high-performance subwoofers, designed specifically for audiophiles and enthusiasts who seek deep and powerful bass response. This subwoofer blends cutting-edge technologies with a sleek design, making it a top choice for both casual listeners and serious sound system builders.

One of the key features of the Kappa 10.5t is its high excursion design. The subwoofer is engineered to offer impressive linear movement, allowing it to produce deep bass frequencies with minimal distortion. This is facilitated by its sturdy cone made from a proprietary material that enhances both durability and sound quality. The cone is lightweight yet rigid, providing a quick response that is essential for accurate bass reproduction.

Another highlight of the Kappa 10.5t is its advanced voice coil cooling technology. The subwoofer features a dual voice coil system that promotes efficient heat dissipation, enabling longer playtimes without compromising performance. This means you can crank up the volume on your favorite tracks without worrying about overheating or damage.

The Kappa 10.5t also includes a robust frame construction made from a die-cast aluminum alloy. This not only adds stability but also reduces unwanted resonances that can muddy the sound. The subwoofer's design incorporates large venting ports that improve air circulation, further reducing thermal build-up and enhancing overall performance.

In terms of power handling, the Infinity Kappa 10.5t boasts an impressive rating, making it suitable for a variety of amplifiers. It is designed to work seamlessly across different setups, from home theaters to car audio systems. Whether you're looking to integrate it into a compact space or a more extensive sound system, the flexibility of the Kappa 10.5t makes it an ideal choice.

Additionally, the aesthetic design of the Kappa 10.5t is noteworthy. The sleek finish and modern styling make it an attractive addition to any setup. Whether mounted in a vehicle or positioned within a home audio arrangement, it enhances both the visual and auditory experience.

Overall, the Infinity Kappa 10.5t is a powerful and versatile subwoofer that provides depth, clarity, and performance. With its advanced technologies, robust construction, and elegant design, it meets the needs of even the most discerning music lovers, delivering an unparalleled listening experience that truly brings your audio to life.