Rhino Mounts 1594 manual Transporting Safety Instructions and Practices

Page 17
(SL-21)
(SL-04)
(SG-19)

SAFETY

Transporting Safety Instructions and Practices

Transport only at speeds where you can maintain control of the equipment. Serious accidents and injuries can result from operating this equipment at high speeds. Understand the Tractor and Implement and

how it handles before transporting on streets and highways. Make sure the Tractor steering and brakes are in good condition and operate properly.

Before transporting the Tractor and Implement, determine the proper transport speeds for you and the equipment. Make sure you abide by the following rules:

Test the tractor at a slow speed and increase the speed slowly. Apply the Brakes smoothly to determine the stopping characteristics of the Tractor and Implement. As you increase the speed of the Tractor the stopping distance increases. Determine the maximum transport speed not to exceed 20 mph (30 kph) for transporting this equipment.

Test the equipment at a slow speed in turns. Increase the speed through the turn only after you determine that the equipment can be operated at a higher speed. Use extreme care and reduce your speed when turning sharply to prevent the tractor and implement from turning over. Determine the maximum turning speed for you and this equipment before operating on roads or uneven ground.

Only transport the Tractor and Implement at the speeds which allow you to properly control the equipment.

Be aware of the operating conditions. Do not operate the Tractor with weak or faulty brakes or worn tires. When operating down a hill or on wet or rain slick roads, the braking distance increases: use extreme care and reduce your speed. When operating in traffic always use the Tractor’s flashing warning lights and reduce your speed. Be aware of traffic around you and watch out for the other guy.

Before transporting the tractor and Loader engage the loader valve travel lock to prevent inadvertent contact with the joystick controller causing sudden dropping of the loader and attachment. If the loader attachment, such as a bucket, were to drop suddenly and hit the ground while transporting, the tractor could stop immediately resulting in the operator hitting the steering wheel or flying our of the operator’s seat. Serious injury could result.

Do not raise the loader on a hillside. Do not transport across a slope with a raised loader. When the loader is raised, the center of gravity of the tractor and loader is raised increasing the potential for the tractor to tip over. Tractor wheel contact with any wash out, drop off or the ground obstruction with a raised loader could result in the tractor tipping over and causing serious bodily injury.

1594 01/11

Safety Section 1-13

© 2011 Alamo Group Inc.

SAFETY

Image 17
Contents 1594 To the Owner/Operator/Dealer Table of Contents Maintenance Section Safety Section General Safety Instructions and Practices Safety1594 01/11 Safety Section Operator Safety Instructions and Practices Safety Equipment Operation Safety Instructions and Practices SG-36 Safety Safety SL-33 Safety Safety Transporting Safety Instructions and Practices Maintenance and Service Safety Instructions and Practices Safety Concluding Safety Instructions and Practices Storage and Parking Safety Instructions and PracticesDecal Location QTY Level Description Decal Description D470 Name 1594 01/11 Safety Section Safety Safety Federal Laws and Regulations Page Introduction Section Introduction Introduction Introduction Before Operating this Machine Page Assembly Section General Information AssemblyPallet Component Removal Preparing TractorInstalling Grille Guard Installing Left and Right Midmounting BracketsMounting Loader to Tractor Plumbing LoaderAttaching Bucket to Loader Attaching Quick Attach and Bucket to Loader Connecting Quick Attach Device OptionalPre-Operation Check Dismounting the Loader Mounting Loader Operation Section Operation Standard Equipment and Specifications Operator Requirements Operation Personal Protective Equipment PPE Rops and Seat Belt Tractor RequirementsTractor Ballast Tractor Lighting and SMV EmblemBoarding the Tractor Getting On and Off the TractorDismounting the Tractor Starting the Tractor Tractor Pre-Operation Inspection/Service Pre-Operation Inspection and ServiceLoader Pre-Operation Inspection and Service Mount Assembly Hydraulic Line Inspection Do not Operate an Unsafe Tractor or Front END Loader Front END Loader PRE-OPERATION Inspection Driving the Tractor and Loader Starting the Tractor Brake and Differential Lock SettingOperating the Tractor and Loader Driving the Tractor and LoaderSG-36 Operation 1594 01/11 Operation Section Operation Filling the Bucket Operating the LoaderOperation Lifting the Load Dumping the Bucket Lowering the Bucket Loading from a Bank Operation Peeling and Scraping Loading LOW Trucks or Spreaders from a Pile Backfilling Operation Handling Large Heavy Objects Operating Bale Spear Valve Lock Loader Storage Transporting the Tractor and Implement Operation Transporting on Public Roadways Hauling the Tractor and Implement Trouble Possible Cause Possible Remedy Troubleshooting GuideMaintenance Section Maintenance 1594 01/11 Maintenance Section Grease Fittings Lubrication ScheduleDaily Maintenance Storage Maintenance Proper Torque for Fasteners Maintenance Maintenance Page Rhino To the OWNER/OPERATOR/DEALER SOM-01/11 F-4282C Printed U.S.A