Redring After Sales Service

b) Pump	Check for faulty potentiometer
operates	switch, (located under knob
when motor	'A' inside front cover). Switch
is switched	should be open circuit when
off	turned fully anti-clockwise.

c)Water too Blockage in filter causing

hot	obstruction in water supply.
	Check and clean (see page 10).

d)Water too Blockage in filter causing

cold	obstruction in water supply.
	Check and clean (see page 10).

Diagram 5

2 metres, typical height for majority of users from top of riser rail to base of bath or cubicle

Diagram 6

e)Poor temperature adjustment

Check that the hot and cold water supplies are delivered to the correct ports.

Check that water is supplied to the shower unit at balanced pressures (ie. Hot and cold water are supplied from the same header tank). Ensure cold supply is not taken from mains.

2 metres typical height from top of riser rail to base of bath or cubicle

f)Unit does Check that the shower and all

not prime pipework are sited below the level of the cold water tank.

g)Poor flow Are there any restrictions in

rate	the 15mm supply (reduced
	diameters even for short
	distances).
	Is the pressure being lost to
	other services in the dwelling.
	Check filter for obstructions in
	the water supply and clean if
	necessary. See page 10 for
	details.

We offer a technical advisory service on the telephone to contractors and other customers with problems in the field.

Ring 0870 9000 430 (Normal Office Hours) Spare parts can be supplied against any VISA or Access cards.

Ring 0870 9000 420 (Normal Office Hours) Remember to quote the exact type of shower, as written on the front of the shower and on this leaflet. It may also be of use to have a note of the Catalogue Number as stated on the rating plate inside the shower (see diagram 2 for location)

INSTALLATION INSTRUCTIONS

The installation should be done by qualified personnel and checked by the Electricity Board.

WARNING: DO NOT INSTALL THE SHOWER IN A ROOM WHERE IT MAY BE SUBJECT TO FREEZING.

We recommend that the installation is done in the following sequence :-

A)Fixing the shower to the wall.

B)Plumbing.

C)Electrical connections.

A) Fixing the shower to the wall

The Redring Expressions Power Shower is fitted with a motor and some mechanical noise can be expected when in use. The type of wall structure will affect the noise levels. Solid walls will provide quieter operation than panel or stud partition walls.

1.Place the riser rail at the height recommended in diagrams 5/6 and mark its position.

2.Position the heater so that the sides of the unit are vertical and that all controls can be comfortably reached whilst the shower is being used. Ensure correct orientation of the shower

520M/520TS specifications

The Redring 520M and 520TS are highly regarded electric water heaters designed for convenience and efficiency in domestic and light commercial applications. Both models exemplify Redring's commitment to delivering innovative heating solutions suitable for various hot water needs.

One of the standout features of the Redring 520M and 520TS is their compact size, making them an ideal choice for installations in limited spaces such as kitchens, bathrooms, or utility rooms. Their sleek design allows them to blend seamlessly into any decor, enhancing aesthetics while providing functionality.

These models are equipped with advanced heating technologies that ensure rapid and consistent water heating. The Redring 520M offers a powerful 2kW heating element, while the 520TS features a slightly higher 3kW option, suitable for environments requiring higher hot water demands. Shoppers can choose between these specifications based on their specific needs.

Both models come with user-friendly controls that allow users to adjust temperature settings with ease. The Redring 520M features a simple dial control, while the 520TS is enhanced with digital controls for more precise temperature management. This versatility ensures users can tailor their hot water experience and adapt to various situations.

Safety is paramount in the design of the Redring 520M and 520TS. They are equipped with overheat protection systems that automatically shut off the unit if the water temperature exceeds a predetermined limit, thus minimizing the risk of scalding. Additionally, an integrated pressure relief valve provides extra safety, ensuring that the unit operates within safe pressure levels.

Energy efficiency is another critical characteristic of both models. The near-instantaneous heating capabilities reduce waiting times and minimize energy wastage compared to traditional water heating systems. Furthermore, the likelihood of water standing idle in a hot water tank is eliminated, leading to significant cost savings over time.

In summary, the Redring 520M and 520TS offer efficient, safe, and reliable hot water solutions. Their compact design, advanced heating technologies, and emphasis on user-friendliness make them perfect additions to any home or small business. With Redring's reputation for quality and innovative engineering, these models serve both functionality and convenience for various hot water needs. The Redring 520M and 520TS stand as exemplary products in modern electric water heating solutions, combining quality, energy efficiency, and ease of use for today's consumers.

hot

cold

rate

distances).