Cable Removal, Cable Installation

INSTALLATION

Use the following procedure to relieve spring tension prior to cable or spring replacement.

!WARNING

DO NOT insert hands into gearbox until springs are fully

detensioned. Doing so could lead to serious injury.

1.Cycle reel thru normal operating cycle and stop when maximum amount of cable is wound onto reel spool.

2.Set spool lock to prevent spool from turning.

3.Remove access cover from top of gearbox.

4.Using open end wrench, loosen large hex nut slowly to allow springs to unwind. Fully loosen nut further with wrench until springs are completely unwound.

5.Repair reel or replace springs or cable as necessary.

6.Retighten nut until definite resistance is felt and spring washers are full compressed (flat). Replace cover.

NOTE: If hex nut is not adequately tightened, spring unwinding can occur during reel operation.

7. Pretension reel. See INSTALLATION section, front page.

CABLE REMOVAL

Use the following procedure to remove worn or damaged cable from reel prior to installation of new cable.

!CAUTION

Failure to relieve all spring tension prior to removing

cable could result in damage to equipment or personal injury. Follow instructions carefully.

1.Move machine serviced by reel to a position closest to reel. Springs will still be under pre-tension at this point.

2.Turn off all electric power.

3.Using spool lock. lock spool to prevent turning.

4.Disconnect cable from machine junction box.

5.Detension springs as described above.

6.Remove cable from spool. Loosen cable clamp and water-tight connector and disconnect conductors from slip ring.

CABLE INSTALLATION

Use the following procedure to replace cable or if reel was ordered without cable. Refer to CABLE INSTALLATION REFERENCE DRAWING, below.

1.Unspool new cable from shipping spool and lay out to eliminate twist.

NOTE: This step is not essential, but will aid in winding operation of the reel and prolong cable life.

2.Feed one end of the cable through water-tight connector on the main shaft inside the spool and into the slip ring side (See drawing below).

NOTE: This may require that jacket of cable be stripped to allow conductors to pass through shaft.

3.Connect individual conductors to appropriate rings on collector using crimp fitting or similar connection method.

4.Tighten water-tight connector and cable clamp in slot on spool disk. Do not over-tighten.

5.Wind the cable onto the reel spool by hand rotating spool in direction it turns free of spring tension.

6.Connect free end of cable to machine junction box.

7.Pretension reel and complete reel installation as previously described.

COLLECTOR REPLACEMENT

1.Turn off all power to reel.

2.Remove collector cover and gasket.

3.Disconnect electric leads to and from collector.

4.Remove drive stud bolt from bearing housing.

5.Remove button plug from hole in side of housing. Insert long 1/8" Allen wrench through hole and loosen two set screws in collector locking collar. Set screws are at 90° to one another.

NOTE: Older reels may have lock screws which must be removed to reach set screws holding collector to shaft.

6.Slide collector off shaft.

7.Install new collector by reversing

Printed in USA

GLEASON REEL CORP.

P.O. Box 26 • 600 South Clark St.

Mayville, WI 53050

Phone 920-387-4120 • Fax 920-387-4189

Bulletin No. 049663.b

SM-28 specifications

The Hubbell SM-28 is a high-performance, multi-purpose device known for its exceptional versatility and reliability across various industrial applications. As part of Hubbell's expansive line of electrical products, the SM-28 is particularly valued for its robust construction and advanced technological features that enhance operational efficiency.

One of the main features of the Hubbell SM-28 is its durable design. Constructed from high-grade materials, the device is built to withstand harsh environmental conditions, making it ideal for outdoor and industrial use. Its rugged housing ensures that it remains resistant to corrosion, moisture, and dust, thereby prolonging its lifespan and reducing maintenance needs.

The SM-28 integrates advanced connectivity technologies, including wireless capabilities that allow for easy integration with existing systems. This feature is particularly beneficial for industries that require constant monitoring and control over their electrical systems. The device supports various communication protocols, enabling seamless interoperability with other Hubbell products and third-party equipment.

Another significant characteristic of the SM-28 is its energy efficiency. Designed to optimize power consumption, the device helps users reduce operational costs while minimizing their carbon footprint. The advanced energy management features enable real-time monitoring and reporting of energy usage, allowing for data-driven decision-making.

The Hubbell SM-28 also boasts a user-friendly interface that simplifies installation and operation. Its intuitive controls and clear display make it easy for operators to manage settings and access critical information. This ease of use is complemented by robust technical support and comprehensive documentation provided by Hubbell, ensuring that users can maximize the device's capabilities.

Safety is a top priority in the design of the SM-28. The device includes various protection features, such as overload and short-circuit protection, which safeguard both the equipment and the personnel operating it. Compliance with industry safety standards further enhances its reliability and credibility.

In summary, the Hubbell SM-28 is a standout solution for various industrial applications, combining durability, advanced technology, energy efficiency, and user-friendly design. With its robust features and high-performance capabilities, the SM-28 is poised to meet the evolving demands of modern industries while ensuring safety and reliability.