Flymo Multi-Trim manual Fault Finding Chart, Manual Line Feed, Spool CAP and Nylon Line 1 Line S

Page 9

FAULT FINDING CHART

WARNING Disconnect from the mains electricity supply before attempting any maintenance or adjustment.

FAULT

LINE NOT FEEDING

OR

LINE TOO SHORT

OR

TRIMMER VIBRATES

CHECK

Is the automatic line feed working?

Is line fed out and visible? (Check for both lines if 2 lines are fitted)

Is the manual line feed working?

 

 

ACTION

 

 

 

 

 

 

No

 

Manually feed out line.

 

SEE “MANUAL LINE FEED”

 

 

 

 

 

 

 

 

Remove cap and spool, free line and

 

 

re-fit spool and cap.

No

 

 

SEE “SPOOL CAP AND NYLON

 

 

LINE”

 

 

 

 

 

 

 

 

The line may be jammed on the spool.

No

 

Rewind line to remove crossed loops.

 

(Check that line is in correct section of

 

 

 

 

spool if 2 lines are fitted)

 

 

 

CONTINUOUS

CLATTERING NOISE

LINE SNAPS

CONTINUOUSLY

Has the motor reached full speed before use?

Has too much line been fed out?

Is the line cutter missing from the safety guard?

Are you using the trimmer correctly?

Is the line jamming on the spool?

No

 

Allow the motor to reach full speed

 

before use

 

 

 

 

 

 

Yes

 

SEE “MANUAL LINE FEED”

 

 

 

 

 

 

Contact your local approved

 

 

Service Centre or Electrolux

Yes

 

 

Outdoor Products Customer

 

 

Service.

 

 

 

?Only use tip of nylon line to trim.

SEE “How to trim and edge”

Yes

 

Rewind the line on the spool, if symptoms

 

still persist, change spool and line.

 

 

 

IF NONE OF THE ABOVE OR IF FAULT PERSISTS

Contact Electrolux Outdoor Products Customer Service Telephone : 01325 300303

MANUAL LINE FEED

To manually feed the nylon line (R)

Please note: Depending on which model you have purchased, your trimmer may be fitted with one line or two lines.

R1-a - Manual Line Feed Button

R2-a - Manual Line Feed Button

1.If required line can be fed out manually.

2.To operate, press and release manual line feed button, whilst gently pulling on the line until it

reaches the line cutter. (If 2 lines are fitted do this to one line only, then gently pull on the second line, there is no need to press the manual line feed

button again).

3.If the line extends past the line cutter, too much line has been fed out.

4.If too much line is fed out, remove the spool cap

and click spool anti-clockwise until the line is at the desired length.

SPOOL CAP AND NYLON LINE (1 LINE) - S

S1-a - Cap Release Latches, S2-a - Cap,

S2-b - Spool, S2-c - Spoolholder, S2-d - Eyelet,

S2-e - Manual Line Feed Button,

S3-a - Eyelet,

S4-a - Hole in Spool, S4-b - Line

 

To remove spool cap

 

1. Press and hold in the two cap release latches.

See

fig S1.

 

2. Pull cap away from the spoolholder.

See fig S2.

When refitting the spool cap

 

1.Keep all areas of the cap and spoolholder clean. Failure to do so may prevent the cap being securely located in the spoolholder.

2.Align the two latches on the cap with the two windows in the spoolholder, then press down into the locked position.

3.Ensure the two cap release latches are clearly visible and

are fully engaged with the windows in the spoolholder.

4.Check that the cap is correctly fitted by trying to remove it without depressing the two latches.

To replace nylon line. Replacement nylon line is available from most Electrolux Outdoor Products stockists. You can buy it either as spool and line complete, or as nylon line only.

To replace spool and line (complete)

1. Unwind approximately 100mm of line and feed this

through eyelet, see fig S3, then drop the spool into

spoolholder smooth side uppermost.

To replace nylon line on spool.

1.Take line and insert into hole in spool.

2.Turn spool clockwise to wind on required amount of

line, (approx. half = 10m) and cut line to length,

see

fig S4. Care should be taken to ensure that the line

 

is neatly coiled on the spool. Failure to do so will

 

impair the efficiency of the automatic line feed.

 

3. Leave approximately 100mm of line unwound and

 

feed this through eyelet,

see fig S3, then drop the

 

spool into the spoolholder

smooth side

 

uppermost.

 

 

Ensure spool is fully located by gently rotating it during fitment.

Remember! Your Flymo Multi-Trim is designed to use only nylon line with a maximum diameter of 1.5mm. Use only genuine Flymo nylon line.

ENGLISH - 3

Image 9
Contents Wichtige Information Important InformationRenseignements Importants Belangrijke InformatieGB Contents Carton Contents Multi Trim Page Multi Trim English HOW to Trim and Edge Assembly InstructionsAuto Line Feed System Before USEFault Finding Chart Manual Line FeedSpool CAP and Nylon Line 1 Line S Guarantee and Guarantee Policy Service RecommendationsSpool CAP and Nylon Line 2 Lines T Caring for Your Multi TrimBELGIQUE/BELGIË Electrolux Group. The world’s No.1 choice