8.Insert a small screwdriver into aligned holes. This will keep the shaft from turn- ing while tightening the blade nut.
Screwdriver
9. Tighten blade nut firmly with a wrench while holding screwdriver in position.
10. Remove the screwdriver.
11. Turn blade by hand. If the blade binds against the shield, or appears to be un- even, the blade is not centered, and you must reinstall.
NOTE: To remove blade, insert screwdriver into aligned holes. Unthread the nut and remove parts. Be sure to store parts and instructions for future use.
KNOW YOUR BRUSHCUTTER ATTACHMENT
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR BRUSHCUTTER ATTACHMENT. Compare the illustrations with your unit to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference.
|
|
|
|
|
|
|
| Hanger | ||||||
|
| Shaft |
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
| Gearbox | |||||||
Trimmer Shield |
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Trimmer Head | Blade Shield |
|
|
|
| Blade | ||||||||
|
|
|
| |||||||||||
BLADE | BLADE SHIELD |
|
|
|
|
|
| |||||||
The BLADE is designed for cutting grass, | The BLADE SHIELD provides protection from | |||||||||||||
weeds, and brush up to 1/2 inch (1 cm) in | the spinning blade. |
|
|
|
|
|
| |||||||
diameter. | TRIMMER SHIELD |
|
|
|
|
|
| |||||||
TRIMMER HEAD | The TRIMMER SHIELD provides protection | |||||||||||||
The TRIMMER HEAD holds cutting line and is | from the spinning trimmer line. | |||||||||||||
designed for cutting grass and light weeds. |
|
|
|
|
|
|
|
|
| |||||
|
|
| ||||||||||||
OPERATING THE COUPLER | 1. Loosen the coupler by turning the knob | |||||||||||||
Your powerhead is equipped with a coupler | counterclockwise. | Upper Shaft | ||||||||||||
which enables optional attachments to be |
|
|
| |||||||||||
installed. The optional attachments are: | Coupler |
|
|
|
|
|
| |||||||
|
| MODEL: |
|
|
|
|
|
| ||||||
Edger . . . . . . . . . . . . . . . . . . . . . . . PPB1000E |
|
|
| LOOSEN | ||||||||||
Cultivator . . . . . . . . . . . . . . . . . . . PPB2000T | Lower | |||||||||||||
|
|
|
|
|
| |||||||||
Blower . . . . . . . . . . . . . . . . . . . . . . PPB3000B | Attachment |
|
|
|
|
|
| |||||||
WARNING: Always disconnect pow- |
|
|
|
|
|
|
|
|
| |||||
erhead spark plug before removing or instal- |
|
|
|
|
|
|
|
|
| |||||
ling attachments. |
|
|
|
|
|
|
|
|
| |||||
REMOVING BRUSHCUTTER | TIGHTEN | Knob | ||||||||||||
ATTACHMENT (OR OTHER |
|
|
|
|
|
|
|
|
| |||||
OPTIONAL ATTACHMENTS) | 2. Press and hold the locking/release button. |
| |
CAUTION: When removing or installing at- |
|
tachments, place the powerhead and attach- |
|
ment on a flat surface for stability. |
|
| 8 |