Poulan 545186849 Carburetor Idle Speed Adjustment, Seasonal Storage, Fuel System, Engine, Other

Page 18

CARBURETOR IDLE SPEED ADJUSTMENT

WARNING: Keep others away when making idle speed adjustments. The trimmer head or any optional attachment will be spin- ning during most of this procedure. Wear your protective equipment and observe all safety precautions. After making adjustments, the trimmer head or any optional attachment must not move/spin at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

S Engine will not idle when the throttle is released.

S The trimmer head or any optional attachment moves/spins at idle.

Make adjustments with the unit supported so the cutting attachment is off the ground and will not make contact with any object.

Hold the unit by hand while running and mak- ing adjustments. Keep all parts of your body away from the cutting attachment and muffler.

To adjust idle speed:

Allow engine to idle. Adjust speed until engine runs without trimmer head or any optional at- tachment moving or spinning (idle too fast) or engine stalling (idle speed too slow).

STurn idle speed screw clockwise to increase engine speed if engine stalls or dies.

S Turn idle speed screw counterclockwise to decrease engine speed if trimmer head or any optional attachment moves or spins at idle.

WARNING: Recheck the idle speed after each adjustment. The trimmer head or any optional attachment must not move or spin at idle speed to avoid serious injury to the operator or others.

Idle Speed Screw

Air Filter Cover

If you require further assistance or are unsure about performing this procedure, contact an authorized service dealer or call 1--800--554--6723.

STORAGE

WARNING: Perform the following steps after each use:

SAllow engine to cool before storing or trans-

porting.

SStore unit and fuel in a well ventilated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

SStore unit with all guards in place. Position

unit so that any sharp object cannot acci- dentally cause injury.

SStore unit and fuel well out of the reach of children.

SEASONAL STORAGE

Prepare unit for storage at end of season or if it will not be used for 30 days or more.

If your unit is to be stored for a period of time:

SCheck entire unit for loose screws or nuts. Replace any damaged, worn or broken parts.

S Clean the entire unit before lengthy storage.

SStore in a clean dry area.

SInspect the blade shield area and clean any dirt, grass, leaves, or debris that has col- lected. Inspect the blade and blade shield; re-

place a blade that is bent, warped, cracked, broken or damaged in any other way.

SLightly oil external metal surfaces.

SApply a coating of oil to the entire surface of the blade; wrap it in heavy paper or cloth.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message la- beled IMPORTANT regarding the use of ga- sohol in your engine.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to the gasoline in the fuel tank or fuel storage container. Fol- low the mix instructions found on stabilizer container. Run engine at least 5 minutes after adding stabilizer.

HELPFUL TIP

During storage of your gas/ oil mixture, the oil will sepa- rate from the gas.

We recommend that you shake the gas can weekly to insure proper blending of the gas and oil.

ENGINE

SRemove spark plug and pour 1 teaspoon of 40:1, 2-cycle engine oil (air cooled) through the spark plug opening. Slowly pull the

starter rope 8 to 10 times to distribute oil.

SReplace spark plug with new one of recom-

mended type and heat range.

SClean air filter.

S Check entire unit for loose screws, nuts, and bolts. Replace any damaged, broken, or worn parts.

SAt the beginning of the next season, use only fresh fuel having the proper gasoline to oil ratio.

OTHER

SDo not store gasoline from one season to another.

SReplace your gasoline can if it starts to rust.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Advertencia AvertissementTable of Contents Identification of Safety SymbolsIdentification of Safety Symbols Safety Rules Operator SafetyOptional Attachments Line Trimmer Safety Edger SafetyRope, string, flailing devices, etc BLOWER/VACUUM Safety Additional Safety RulesFuel Safety Transporting and StorageBrushcutter Safety Cultivator SafetyHedge Trimmer Safety Another Pole Pruner SafetySnow Thrower Safety Or brokenAssembly Installing Trimmer or Edger AttachmentsAdjusting the Assist Handle Operation HOW to Stop Your Unit Trimmer Head Depth Adjustment KnobHOW to Start Your Unit BladeStarting a Warm Engine Installing Optional ATTACH- MentsOperating Instructions Starting a Flooded EngineTrimmer Line Advance Line Trimmer AttachmentOperating Position Cutting MethodsEdging Setting the Edging DepthEdger Attachment MowingMaintenance Service and Adjustments Replacing the LineEdger Blade Replacement Replacing the Trimmer HeadScrewdriver Fuel System Carburetor Idle Speed AdjustmentSeasonal Storage EngineTroubleshooting Table Cause Remedy Poulan PRO Limited WarrantyCanada, contact Ligations The U.S. EnvironmentalIntermediate 125 hours Extended 300 hours

PP25E, 545186849 specifications

The Poulan 545186849, also known as the PP25E, is a versatile and robust outdoor power tool designed for residential use. It combines user-friendliness with advanced technology, making it an excellent option for homeowners who need reliable performance for lawn care and maintenance tasks. This model is particularly notable for its ergonomic design and lightweight construction, enhancing user comfort and reducing fatigue during extended periods of operation.

One of the main features of the PP25E is its 25cc, 2-cycle engine. This power unit provides adequate power for various tasks, including trimming, edging, and cutting through tough grass and weeds. The engine has been engineered for smooth operation and easy starting, thanks to its reliable starter system. This ensures that users can quickly get to work without the frustration of dealing with difficult starts often associated with some outdoor power equipment.

Another key characteristic of the Poulan PP25E is its versatility. The machine boasts a detachable powerhead that can be coupled with various attachments, such as lawn edgers, cultivators, and pruners. This adaptability allows homeowners to customize their equipment for different tasks, further enhancing its value and functionality. The ease of swapping out attachments makes it an excellent choice for those looking to streamline their outdoor maintenance routine.

User comfort is paramount in the design of the PP25E. The trimmer features an adjustable handle that allows users to tailor the operation to their height, ensuring optimal control and comfort. Additionally, the anti-vibration system incorporated into the design minimizes hand and arm fatigue, allowing for longer usage without discomfort.

The Poulan PP25E also incorporates advanced technologies to enhance its performance. The engine is designed to be highly fuel-efficient, which not only extends run time but also reduces emissions, aligning with environmental standards. The easy-access air filter simplifies maintenance, ensuring that users can keep their equipment in peak condition with minimal effort.

In summary, the Poulan 545186849 PP25E is a highly functional outdoor power tool equipped with a powerful yet efficient engine, versatile attachments, and user-friendly features. Its thoughtful design prioritizes comfort and ease of use, making it an excellent choice for homeowners seeking a reliable solution for their lawn care needs.
Top Page Image Contents