Poulan PP446, 530164083 Starting a Warm Engine, Starting a Flooded Engine, Operating the Coupler

Page 11

NOTE: If engine dies with the choke lever

1. Loosen the coupler by turning the knob

in the OFF CHOKE position, move the choke lever to the HALF CHOKE position and pull the rope until engine runs, but no more than 6 pulls.

counterclockwise.

Coupler

Upper Shaft

Choke position

Lower Attachment

LOOSEN

decal

STARTING A WARM ENGINE

1.Move ON/OFF switch to the ON position.

2.Move the choke lever to the HALF CHOKE position.

3.Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until the engine runs smoothly.

4.Pull starter ropesharply until engine runs, but no more than 5 pulls.

5.Allow engine to run 15 seconds, then move the choke lever to the OFF CHOKE position.

NOTE: If engine has not started, pull starter rope 5 more pulls. If engine still does not run, it is probably flooded.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the choke lever in the OFF CHOKE position; then, pull the rope to clear the engine of ex- cess fuel. This could require pulling the starter handle many times depending on how badly the unit is flooded.

If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723.

OPERATING THE COUPLER

This model is equipped with a coupler which enables optional attachments to be installed. The optional attachments are:

MODEL: Edger . . . . . . . . . . . . . . . . . . . . . . . PP1000E Cultivator . . . . . . . . . . . . . . . . . . . . PP2000T Blower . . . . . . . . . . . . . . . . . . . . . . PP3000B Brushcutter . . . . . . . . . . . . . . . . . . PP4000C

WARNING: Always stop unit anddis- connect spark plug before removing or instal- ling attachments.

REMOVING PRUNER ATTACHMENT (OR OTHER OPTIONAL ATTACH-

MENTS)

CAUTION: When removing or installing at- tachments, place the unit on a flat surface for

stability.

TIGHTEN Knob

2.Press and hold the locking/release button. Locking/Release

Button

Coupler

Upper Shaft

Lower Attachment

 

3.While securely holding the engine and upper shaft, pull the attachment straight out of the coupler.

INSTALLING OPTIONAL ATTACH- MENTS

1. Remove the shaft cap from the attach- ment (if present).

2. Position locking/release button of attach- ment into guide recess of coupler.

3. Push the attachment into the coupler until the locking/release button snaps into the primary hole.

4. Before using the unit, tightenthe knob se- curely by turning clockwise.

Coupler Primary Hole

Guide Recess

Upper Locking/ Attachment

Shaft Release

Button

WARNING: Make sure the locking/ release button is locked in the primary hole and the knob is securely tightened before op- erating the unit.

INSTALLING ATTACHMENT HANGER

An attachment hanger is provided for storage when attachment is not in use.

To install hanger on attachment:

1.Remove the shaft cap from the attach- ment (if present) and discard.

2.Press and hold the locking/release button.

3.Push hanger onto the attachment until the locking/release button snaps into the hole.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents 10/31/03 Manual de Instrucciones Manuel d’InstructionsHazard Zone Plan AheadKickback Operate Your Pruner SafelyMaintain Your Pruner in Good Working Order Handle Fuel with CautionTip Kickback Safety FeaturesReduce the Chance Kickback Maintain ControlFor Optional Attachments Line Trimmer SafetyEdger Safety Away from the operator BLOWER/VACUUM SafetyBrushcutter Safety Cultivator SafetySnow Thrower Safety Hedge Trimmer SafetyTools Required Installing Pruner ATTACH- MentShoulder Strap Assembly Adjusting the Assist HandleCoupler ON/OFF SwitchKnow Your Pruner Primer BulbSee the Storage section for additional in- formation HOW to Stop Your UnitHOW to Start Your Unit Starting a Flooded Engine Installing Optional ATTACH- MentsInstalling Attachment Hanger Starting a Warm EnginePruning Technique Operating PositionPruning Important Points Check Chain Tension Inspect and Clean Unit and LA- BelsCheck for Loose Fasteners and Parts Check for Damaged or Worn PartsLubrication Clean AIR FilterBAR Maintenance Chain ReplacementTo Replace Chain Chain AdjustmentCarburetor Adjustment Idle Speed AdjustmentOther Seasonal StorageFuel System EngineCarbon build-up on Troubleshooting Table Cause RemedyLoad Adjustment Compression lowTions The U.S. Environmental Protection Home PRODUCTS, INC., for this tool. AddiExtended 300 hours Ered. ADD-ON or Modified Parts

PP446, 530164083 specifications

The Poulan PP446,530164083 is a versatile and efficient outdoor power tool that caters to various user needs in lawn and garden maintenance. With its robust design and advanced features, it serves as an excellent choice for both professional landscapers and homeowners looking to maintain their green spaces effectively.

One of the main attractions of the Poulan PP446 is its lightweight construction, making it easy to handle and maneuver while working in diverse landscapes. Weighing approximately 12 pounds, it reduces user fatigue, allowing for extended periods of use without discomfort. This is particularly beneficial when performing tasks such as trimming bushes or hedges where precision and control are vital.

The PP446 features a powerful engine designed to deliver ample power while ensuring efficiency. The engine is environmentally friendly, equipped with a low-emission technology that meets strict EPA standards. This not only promotes eco-friendliness but also offers users peace of mind when using the tool, knowing they are contributing to a cleaner environment.

Enhanced user experience comes from the ergonomic handle design, which provides a comfortable grip during operation. The vibration-dampening technology incorporated into the handle helps to reduce fatigue, making it suitable for prolonged use. This design consideration is crucial for those engaging in intensive tasks or those who may have concerns about strain and discomfort.

The Poulan PP446 also showcases easy-start technology, which simplifies initiation even in cold weather conditions. This user-friendly feature minimizes the hassle often associated with starting outdoor power equipment, allowing users to get to work quickly and efficiently without unnecessary delays.

In terms of maintenance, the PP446 is designed for convenience, featuring easy-access air filters and fuel tanks that simplify the upkeep process. This means less time spent on maintenance and more time focused on the tasks at hand. Additionally, the tool's high-quality materials contribute to its durability, ensuring it withstands the rigors of regular use.

Overall, the Poulan PP446,530164083 combines efficiency, durability, and user-friendly features to create a reliable tool for lawn care and landscaping. Its technology-driven design, coupled with a commitment to environmental sustainability, makes it a standout choice for those seeking to enhance their outdoor spaces with ease. Whether you need a dependable tool for occasional trimming or regular maintenance, the PP446 rises to the occasion, ensuring beautiful results in any garden or yard.
Top Page Image Contents