Poulan 2001-05, 530088909 Cutting Safety, Transporting and Storage, Adjust the Assist Handle

Page 3

S Always store gasoline in a container ap- proved for flammable liquids.

CUTTING SAFETY

WARNING: Inspect the area before each use. Remove objects (rocks, broken glass, nails, wire, etc.) which can be thrown by or become entangled in line. Hard objects can damage trimmer head and be thrown causing serious injury.

SUse only for trimming, mowing, and sweep-

ing. Do not use for edging, pruning, or hedge trimming.

SKeep firm footing and balance. Do not over-

reach.

SKeep all parts of your body away from spin- ning line and muffler. Keep engine below waist

level. A hot muffler can cause serious burns. S Cutting with the line on right side of the shield will throw debris away from the oper-

ator.

SUse only in daylight or good artificial light.

TRANSPORTING AND STORAGE

SAllow the engine to cool; secure unit before storing or transporting in vehicle.

SEmpty the fuel tank before storing or trans- porting the unit. Use up fuel left in the car-

buretor by starting the engine and letting it run until it stops.

SStore unit and fuel in an area where fuel va- pors cannot reach sparks or open flames

from water heaters, electric motors or switches, furnaces, etc.

SStore unit so line limiter blade cannot acci- dentally cause injury. Unit can be hung by the tube.

SStore the unit out of the reach of children If situations occur which are not covered in this manual, use care and good judgment. If you need assistance, call 1-800-554-6723.

SAFETY NOTICE: Exposure to vibrations through prolonged use of gasoline powered hand tools could cause blood vessel or nerve damage in the fingers, hands, and joints of people prone to circulation disorders or ab- normal swellings. Prolonged use in cold weather has been linked to blood vessel dam- age in otherwise healthy people. If symptoms occur such as numbness, pain, loss of strength, change in skin color or texture, or loss of feeling in the fingers, hands, or joints, discontinue the use of this tool and seek med- ical attention. An anti--vibration system does not guarantee the avoidance of these prob- lems. Users who operate power tools on a continual and regular basis must monitor closely their physical condition and the condi- tion of this tool.

SPECIAL NOTICE: This unit is equipped with a temperature limiting muffler and spark arresting screen which meets the require- ments of California Codes 4442 and 4443. All U.S. forest land and the states of California, Idaho, Maine, Minnesota, New Jersey, Ore- gon, and Washington require by law that

many internal combustion engines be equipped with a spark arresting screen. If you operate in a locale where such regulations ex- ist, you are legally responsible for maintaining the operating condition of these parts. Failure to do so is a violation of the law. For normal homeowner use, the muffler and spark arrest- ing screen will not require any service. After 50 hours of use, we recommend that your muffler be serviced or replaced by your Au- thorized Service Dealer.

WARNING: Make sure your unit is properly assembled and all fasteners are se- cure.

ADJUST THE ASSIST HANDLE

SLoosen handle by turning T--handle/screw

counterclockwise.

S Rotate handle to upright position on the tube.

SAdjust handle to a comfortable position be- tween the trigger and the safety label on the

tube.

S Retighten handle securely by turning T-- handle/screw clockwise.

ATTACH THE SHIELD

WARNING: The shield must be prop- erly installed. The shield provides partial protection from the risk of thrown objects to the operator and others and is equipped with a line limiter blade which cuts excess line to the proper length. The line limiter blade (on underside of shield) is sharp and can cut you.

SRemove wing nut from shield.

SInsert bracket into slot as shown.

SPivot shield until bolt passes through hole in bracket.

SSecurely tighten wing nut onto bolt.

SThread trimmer head onto shaft; tighten se- curely against dust cup by turning counter- clockwise (trimmer head may already be installed on the unit).

Bracket

Wing Nut

 

 

 

 

 

 

 

 

 

Slot

Dust Cup

Shield

3

Image 3
Contents Manual de Instrucciones Manuel d’Instructions Safety Glasses or similar eye protection Operator SafetyUnit / Maintenance Safety Fuel SafetyAttach the Shield Cutting SafetyAdjust the Assist Handle Transporting and StorageFlooded Engine HOW to Stop Your UnitHOW to Start Your Unit Starting a Warm EngineReplacing the Cutting Head Carburetor AdjustmentsStarting a Flooded Engine Operating PositionTroubleshooting Table Cause Remedy See Carburetor AdjustmentsHead Use only 0.080 2 mm dia. line