Poulan BC2500 LE Attaching the Plastic Shield and Trimmer Head, Assembly Information Weed Blade

Page 5

NOTE: Remove the blade and metal shield before attaching the plastic shield and trim- mer head. To remove blade, push in locking lever and hold. Rotate blade nut until the lock- ing lever falls into one of the grooves in the dust cup. Continue to hold the locking lever. This will keep the shaft from turning while loosening the blade nut. Remove blade nut by turning clockwise. Release locking lever. Remove both washers and blade. To remove metal shield, loosen and remove the four mounting screws. See ATTACHING THE METAL SHIELD and INSTALLATION OF THE METAL BLADE for illustrations. Be sure to store all parts and instructions for future use.

ATTACHING THE PLASTIC SHIELD AND TRIMMER HEAD

8.Thread trimmer head onto the shaft in the direction shown on the decal. Tighten un- til secure.

9.Release locking lever.

ASSEMBLY INFORMATION - WEED BLADE

WEED

BLADE

WARNING: The shield must be prop- erly installed. The shield provides partial protection to the operator and others from the risk of thrown objects, and is equipped with a line limiter blade which cuts excess line to the proper length. The line limiter blade (on un- derside of shield) is sharp and can cut you.

1.Remove wing nut from shield.

2.Insert bracket into slot on shield.

3.Pivot shield until bolt passes through hole in bracket.

4.Tighten the wing nut securely.

NOTE: If your unit has a plastic cover over the threads on the threaded shaft, remove the cov- ering to expose the threads. Before installing the trimmer head, make sure the dust cup is positioned on the gearbox as shown below.

 

Bracket

Slot

Wing Nut

 

Shield Gearbox

Dust Cup

NOTE: Make sure all parts are properly installed as shown in the illustration before installing the trimmer head.

5.Push in locking lever and hold.

6.Rotate dust cup until the locking lever falls into one of the grooves.

Locking Lever

7.Continue to hold in locking lever. This will keep the shaft from turning while tighten- ing the trimmer head.

5

NOTE: Remove the trimmer head and plas- tic shield before attaching the metal shield and installing one of the weed blades. To re- move the trimmer head, push in locking lever and hold. Rotate trimmer head until the lock- ing lever falls into one of the grooves in the dust cup. Continue to hold in locking lever. This will keep the shaft from turning while loosening the cutting head. To remove the plastic shield, loosen and remove wing nut. Pivot shield to release bracket from slot. See

INSTALLATION OF THE CUTTING HEAD and ATTACHING THE PLASTIC SHIELD for illustrations. Be sure to store all parts and in- structions for future use. Never use the trim- mer head with the metal blade installed.

ATTACHING THE METAL SHIELD

WARNING: The metal shield must be properly installed on the tool anytime the tool is used with a blade. The forward tip of the metal shield helps to reduce the occurrence of blade thrust which can cause serious injury such as amputation to the operator or by- standers. Failure to install the shield in the position shown can result in serious injury to the operator. The length of the shield must be aligned with the length of the tube.

1.Place the metal shield under the gearbox, and align the screw holes.

Gearbox

Shield

2.Insert and thread the 4 mounting screws through the holes of the gearbox and the metal shield. Tighten evenly and secure- ly with the hex wrench provided.

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Manual de Instrucciones Manuel d’Instructions Always Wear Operator SafetyFuel Safety UNIT/MAINTENANCE SafetyCutting Safety Transporting and StorageAssembly of Shoulder Strap Carton ContentsConfiguring Your Unit Assembly Information Trimmer HeadAttaching the Plastic Shield and Trimmer Head Assembly Information Weed BladeAttaching the Metal Shield Weed BladeInstallation of the Metal Blade HOW to Stop Your Unit ON/OFF SwitchKnow Your Brushwacker Primer BulbStarting a Warm Engine HOW to Start Your UnitStarting a Flooded Engine Operating PositionCutting Methods Operating Instructions for USE with Trimmer HeadTrimmer Line Advance Recommended Cutting Position Operating Instructions for USE with Weed BladeClean AIR Filter Inspect and Clean Unit and DE- CalsCheck for Loose Fasteners and Parts Check for Damaged or Worn PartsCarburetor Adjustment Blade ReplacementReplacing the Line Seasonal StorageTroubleshooting Table Cause Remedy Electrolux Home PRODUCTS, INC POULAN/WEED Eater Warranty Period

BC2500 LE specifications

The Poulan BC2500 LE is a reliable and efficient string trimmer designed for homeowners and gardening enthusiasts seeking a lightweight yet powerful solution for yard maintenance. Known for its user-friendly features and robust performance, the BC2500 LE stands out in the market of outdoor power tools.

Equipped with a 25cc two-cycle engine, the Poulan BC2500 LE delivers impressive power for tackling even the toughest weeds and grass. This engine is designed for optimal performance, providing a balance between power and efficiency while minimizing emissions. Its lightweight design, weighing only around 10 lbs, makes it easy to maneuver, reducing fatigue during extended use.

One of the standout features of the BC2500 LE is its ergonomic handle design. The trimmer is equipped with a comfortable and adjustable handle that allows users to find the perfect grip and angle for their work. This adjustability not only enhances comfort but also increases precision in cutting, making it easier to navigate around flower beds, fences, and other obstacles.

The Poulan BC2500 LE utilizes a dual-line feed system, which allows for a wider cutting path of 17 inches. This feature increases efficiency by covering more ground with each pass, enabling users to complete their trimming tasks more quickly. The automatic line advance mechanism ensures that the cutting line is continuously fed as needed, simplifying the process of line replacement.

Another noteworthy technology implemented in the BC2500 LE is its simplified starting system. This feature significantly reduces the effort required to start the engine, allowing users to get to work without the frustration that can come from pull-start engines. The inclusion of an easy-to-use primer bulb and choke helps ensure a reliable start every time.

Durability is also a key characteristic of the Poulan BC2500 LE. The trimmer is crafted with high-quality materials designed to withstand the wear and tear of outdoor use. The protective guard helps to shield the engine and internal components, extending the life of the equipment.

In summary, the Poulan BC2500 LE string trimmer combines power, efficiency, and user-friendly features, making it an excellent choice for homeowners looking for a dependable tool for lawn care and maintenance. Its powerful engine, lightweight design, comfortable ergonomics, and innovative technologies ensure a terrific trimming experience, making yard work less of a chore and more of an enjoyable activity.
Top Page Image Contents