Service and Adjustments, Replacing the Line

SERVICE AND ADJUSTMENTS

REPLACING THE LINE

1.Remove spool by firmly pulling on tap button.

2.Clean entire surface of hub and spool.

3.Replace with a pre-wound spool, or cut two lengths of 12-1/2 feet (3.8 meters) of 0.080″ (2 mm) diameter Poulan PRO brand line.

WARNING: Never use wire, rope, string, etc., which can break off and become a dangerous missile.

4.Insert ends of the lines about 1/2 inch (1 cm) into the small holes on the inside of spool.

Spool

Small

Holes

Line exit holes

Line in Notch

Hub

5.Wind the line evenly and tightly onto the spool. Wind in the direction of the arrows found on the spool.

6.Push the lines into the notches, leaving 3 to 5 inches (7 -- 12 cm) unwound.

7.Insert the lines into the the exit holes in the hub as shown in the illustration.

8.Align the notches with the line exit holes.

9.Push spool into hub until it snaps into place.

10.Pull the lines extending outside of the hub to release the lines from the notches.

REPLACING THE CUTTING HEAD

1.Align hole in the dust cup with the hole in the side of the gearbox by rotating the dust cup.

2.Insert a small screwdriver into aligned holes. This will keep the shaft from turning while removing and installing trimmer head.

Screwdriver

3.While holding the screwdriver in position, remove trimmer head by turning clock- wise.

4.Thread replacement trimmer head onto the shaft by turning counterclockwise. Tighten until secure.

5.Remove the screwdriver.

CARBURETOR ADJUSTMENT

WARNING: Keep others away when making idle speed adjustments. The trimmer head, blade or any optional attachment will be spinning during most of this procedure. Wear your protective equipment and observe all safe- ty precautions. After making adjustments, the trimmer head, blade or any optional attachment must not move/spin at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

S Engine will not idle when the throttle is released.

S The trimmer head, blade or optional attachment moves/spins at idle.

Make adjustments with the unit supported so the cutting attachment is off the ground and will not make contact with any object. Hold the unit by hand while running and making ad- justments. Keep all parts of your body away from the cutting attachment and muffler.

Idle Speed Adjustment

Allow engine to idle. Adjust speed until engine runs without trimmer head, blade or optional attachment moving or spinning (idle too fast) or stalling (idle speed too slow).

S Turn idle speed screw clockwise to increase engine speed if engine stalls or dies.

STurn idle speed screw counterclockwise to decrease engine speed if trimmer head, blade or optional attachment moves or spins at idle.

WARNING: Recheck the idle speed after each adjustment. The trimmer head, blade or optional attachment must not move or spin at idle speed to avoid serious injury to the operator or others.

Air Filter

Cover

Idle Speed

Screw

If you require further assistance or are unsure about performing this procedure, contact an

authorized			service dealer or call
1--	800--	554--	6723.

PPB200 specifications

The Poulan PPB200 is a highly efficient and versatile leaf blower that has gained popularity among homeowners and landscaping professionals alike. Known for its reliable performance and user-friendly design, the PPB200 is engineered to make yard maintenance a breeze.

One of the standout features of the Poulan PPB200 is its powerful 25cc two-cycle engine. This engine delivers a robust airflow speed of up to 200 miles per hour, enabling users to tackle both light and heavy debris removal with ease. Whether you're clearing leaves, grass clippings, or twigs, the PPB200's impressive power makes it an effective tool for keeping your outdoor space tidy.

The PPB200 also boasts a lightweight design, weighing in at just around 13 pounds. This makes it easy to handle, even during extended periods of use. The ergonomic design includes a padded handle and a throttle control that allows for comfortable operation, reducing fatigue and providing users with better control over the blower's power and speed. The backpack design also distributes the weight evenly, allowing for prolonged use without discomfort.

To enhance its performance, the Poulan PPB200 is equipped with an air purge primer bulb, which helps eliminate air from the fuel system and facilitates easier starting. The easy-start technology integrated into the engine ensures a hassle-free ignition, minimizing the time spent trying to get the blower up and running.

Another key feature is its innovative fan design, which maximizes airflow and amplifies suction power. This design not only helps in efficiently moving debris but also reduces noise levels during operation, making it a more pleasant experience for users and neighbors alike.

The Poulan PPB200 offers multiple nozzle attachments, allowing users to switch between different tasks easily. This adds to its versatility, making it suitable for various applications, including sweeping hard surfaces and blowing debris from hard-to-reach areas.

In summary, the Poulan PPB200 is a reliable and efficient leaf blower that combines power, comfort, and ease of use. With its formidable engine, lightweight structure, and convenient features, it is an ideal choice for anyone looking to maintain their yard effectively while saving time and effort. Whether you're a seasoned landscaper or a homeowner, the PPB200 is equipped to meet your outdoor cleanup needs with efficiency and style.