TROUBLESHOOTING
PROBLEM | POSSIBLE CAUSE | SOLUTION | |||
|
|
|
|
|
|
Engine will not start: | 1. | No spark. | 1. | To check for spark: Disconnect the spark plug | |
|
|
|
| wire. Reattach the spark plug wire and lay spark | |
|
|
|
| plug on metal cylinder. Pull the starter rope and | |
|
|
|
| watch for spark at spark plug tip. If there is no | |
|
|
|
| spark, repeat test with a new spark plug. | |
| 2. | No fuel. | 2. | Push primer bulb until bulb is full of fuel. If | |
|
|
|
| bulb does not fill, primary fuel delivery system | |
|
|
|
| is blocked. Contact a service dealer. If primer | |
|
|
|
| bulb fills, engine may be flooded (see next | |
|
|
|
| item). | |
| 3. | Flooded engine. | 3. | Remove spark plug, turn trimmer so spark plug | |
|
|
|
| hole is aimed at the ground. Move choke lever | |
|
|
|
| to “RUN” and pull starter cord 10 to 15 times. | |
|
|
|
| This will clear excess fuel from engine. Clean | |
|
|
|
| and reinstall spark plug. Pull starter three | |
|
|
|
| times with choke lever at “RUN”. If engine | |
|
|
|
| does not start, move choke lever to “CHOKE” | |
|
|
|
| and repeat normal starting procedure. If engine | |
|
|
|
| still fails to start, repeat procedure with a new | |
|
|
|
| spark plug. | |
| 4. | Starter rope pulls harder now than | 4. | Contact a service dealer. | |
|
| when new. |
|
|
|
|
|
| |||
Engine starts but will not | Carburetor requires adjustment. | Contact a service dealer. | |||
accelerate: |
|
|
|
|
|
|
|
| |||
Engine starts but will only | Carburetor requires adjustment. | Turn mixture needle counterclockwise 1/16 turn. | |||
run at high speed at half |
|
| See Figure 22. | ||
choke: |
|
|
|
|
|
|
|
|
|
| |
Engine does not reach full | 1. | Check oil fuel mixture. | 1. | Use fresh fuel and the correct | |
speed and emits excessive | 2. | Air filter dirty. | 2. | Clean air filter. Refer to “Replacing and | |
smoke: |
|
|
| Cleaning Air Filter” earlier in this manual. | |
| 3. | Carburetor requires adjustment. | 3. | Turn mixture needle clockwise 1/16 turn. See | |
|
|
|
| Figure 22. | |
|
|
| |||
Engine starts, runs, and | Carburetor requires adjustment. | Turn idle speed screw clockwise to increase idle | |||
accelerates but will not |
|
| speed. See Figure 22. | ||
idle: |
|
|
|
|
|
|
|
|
|
| |
String will not advance: | 1. | String welded to itself. | 1. | Lubricate with silicone spray. | |
| 2. | Not enough string on spool. | 2. | Install more string. Refer to “String Replace- | |
|
|
|
| ment” earlier in this manual. | |
| 3. | String worn too short. | 3. | Pull strings while alternately pressing down on | |
|
|
|
| and releasing spool retainer. | |
| 4. | String tangled on spool. | 4. | Remove string from spool and rewind. Refer to | |
|
|
|
| “String Replacement” earlier in this manual. | |
| 5. | Engine speed too slow. | 5. | Advance string at full throttle. | |
|
|
|
|
|
|
Page 16