Homelite F2035, UT70123 manual Troubleshooting, Dealer. See Figure

Page 16

TROUBLESHOOTING

IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM, CONTACT YOUR AUTHORISED SERVICE DEALER.

PROBLEM

POSSIBLE CAUSE

SOLUTION

 

 

 

Engine will not start:

1. No spark.

2.No fuel.

3.Flooded engine.

4.Starter rope pulls harder now than when new.

1.Check spark. Remove sparking plug. Reattach the sparking plug cap and lay sparking plug on metal cylinder. Pull the starter rope and watch for spark at sparking plug tip. If there is no spark, repeat test with a new sparking plug.

2.Push primer bulb until bulb is full of fuel. If bulb does not fill, primary fuel delivery system is blocked. Contact a service dealer. If primer bulb fills, engine may be flooded (see next item).

3.Remove sparking plug, turn trimmer so sparking plug hole is aimed at the ground. Move choke lever to “RUN” and pull starter cord 10 to 15 times. This will clear excess fuel from engine. Clean and reinstall sparking plug. Pull starter three times with choke lever at “RUN”. If engine does not start, move choke lever to “CHOKE” and repeat normal starting procedure. If engine still fails to start, repeat procedure with a new sparking plug.

4.Contact a service dealer.

Engine starts but will not

Carburettor requires adjustment.

Turn “H” needle anticlockwise 1/16 turn. If “L”

accelerate:

 

low needle cannot be turned anticlockwise, do not

 

 

force plastic limiter caps. Contact a service

 

 

dealer. See Figure 22.

 

 

 

Engine starts but will only

Carburettor requires adjustment.

Turn “H” needle anticlockwise 1/16 turn. If “H”

run at high speed at half

 

high needle cannot be turned anticlockwise, do

choke:

 

not force plastic limiter caps. Contact a service

 

 

dealer. See Figure 22.

Engine does not reach full

1.

Check oil fuel mixture.

speed and emits excessive

2.

Air filter dirty.

smoke:

 

 

 

3.

Carburettor requires adjustment.

1.Use fresh fuel and the correct 2-cycle oil mix.

2.Clean the air filter. Refer to “Replacing and Cleaning the Air Filter ” earlier in this manual.

3.Turn “H” needle clockwise 1/16 - 1/8 turn. See Figure 22.

Engine starts, runs, and

Carburettor requires adjustment.

Turn idle speed screw clockwise to increase

accelerates but will not idle:

 

idle speed.

String will not advance:

1.

String welded to itself.

 

2.

Not enough string on spool.

 

3.

String worn too short.

 

4.

String tangled on spool.

 

5.

Engine speed too slow.

1.Lubricate with silicone spray.

2.Install more string. Refer to “String Replacement” earlier in this manual.

3.Pull strings while alternately pressing down on and releasing spool retainer.

4.Remove string from spool and rewind. Refer to “String Replacement” earlier in this manual.

5.Advance string at full throttle.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents OPERATOR’S Manual Safety Table of ContentsSpecific Safety Rules for Trimmer USE Symbols Symbol Name ExplanationTechnical Data Vibration level racingFeatures UnpackingInstructions Packing List for OWNER’S KITSilencer Guard Assembly AssemblySee Figure Edger Guide Assembly Assembly InstructionsWing NUT Lock Washer Long Bolt Flat Operation Fuel and RefuellingHandling the Fuel Safely Mixing the FuelAdvancing String Using the EZ Line TAP Advance System Operating the TrimmerAdvancing the String Cutting TipsGrass Deflector Line Trimming CUT-OFF Blade Edger Guide Operation Trim ‘N Edge OnlySee Figures 10 Wing NUT Edger GuideIgnition Switch Starting and StoppingTo Start a Cold Engine To Start a Warm EngineMaintenance Spool Replacement EZ Line TAP Advance SystemNEW PRE-WOUND Spool See Figures 14Cleaning the Exhaust Port and Silencer String ReplacementSpark Arrester Arrows on Spool Anchor Hole First StringReplacing and Cleaning AIR Filter Fuel CAPSparking Plug Storage 1MONTH or LongerTroubleshooting Dealer. See FigureIdle Speed Screw Needle Warranty Safety DirectiveGuarantee Statement Rtsa / Rtuk / RTG Sound Pressure Sound Power Vibration Model Model noPage Ryobi Technologies GmbH

UT70123, F2035 specifications

The Homelite UT70123 F2035 is a powerful and versatile electric chainsaw designed for both DIY enthusiasts and professionals. Known for its efficiency and user-friendly design, this chainsaw offers a range of features that make it an essential tool for various cutting tasks, from tree trimming to firewood preparation.

One of the standout features of the UT70123 F2035 is its robust 14-amp motor. This powerful motor delivers excellent cutting performance, allowing users to tackle a variety of projects with ease. The chainsaw is designed for swift cuts, making it suitable for both small branches and larger logs. The high power ensures that users can complete their tasks quickly without the hassle of downtime.

Another significant characteristic is the tool-less chain tensioning system, which simplifies the process of adjusting the chain. Users can easily tighten or replace the chain without the need for additional tools, making maintenance straightforward and user-friendly. This feature significantly reduces time spent on setup and ensures optimal chain performance during use.

The Homelite UT70123 F2035 is equipped with a 16-inch cutting bar, providing an excellent reach for various cutting applications. This length strikes a balance between maneuverability and cutting capacity, making it suitable for a range of tasks, from light trimming to heavier pruning jobs. The built-in safety features, including an electric brake and low kickback chain, enhance user safety by minimizing the risk of accidents during operation.

In terms of design, the chainsaw is ergonomically built with a comfortable grip handle, reducing fatigue during extended use. It also features a lightweight design, further contributing to user comfort. The chainsaw includes a transparent oil tank, allowing users to monitor oil levels for optimal chain lubrication.

Lastly, the UT70123 F2035 operates quietly compared to gas-powered alternatives, making it ideal for residential areas. This electric chainsaw not only delivers efficient performance but also helps to create a less disruptive cutting experience.

In summary, the Homelite UT70123 F2035 combines a powerful motor, tool-less chain adjustment, safety features, and ergonomic design. Whether for light gardening tasks or more intensive woodcutting projects, this chainsaw provides reliability and efficiency for all your cutting needs.
Top Page Image Contents