Ryobi 780r manual While Operating with Cutting Blade

Page 6

RULES FOR SAFE OPERATION

WHILE OPERATING WITH CUTTING BLADE

•Read and understand all safety warnings before operating this unit.

•Always use the shoulder harness when using the brush blade accessory.

•Keep the handle between the operator

and cutting attachment or blade at all times.

•NEVER cut with the cutting blade located over 30 inches (76 cm) or more above the ground level.

•Blade thrust may occur when the spinning blade contacts an object that it does not immediately cut. Blade thrust can be violent enough to cause the unit and/or operator to be propelled in any direction , and possibly lose control of the unit. Blade thrust can occur without warning if the blade snags, stalls or binds. This is more likely to occur in areas where it is difficult to see the material being cut.

•For operation with the brush blade, do not cut anything thicker than 1/2 inch or a violent kickback could occur.

•Do not attempt to touch or stop the blade when it is rotating.

•A coasting blade can cause injury while it continues to spin after the engine is stopped or the throttle trigger is released. Maintain proper control until the blade has completely stopped rotating.

•Do not run the unit at high speed when not cutting.

•If you strike or become entangled with a foreign object, stop the engine immediately and check for damage. Have any damage repaired before attempting further operations. Do not operate unit with a bent, cracked or dull blade. Discard blades that are bent, warped, cracked or broken.

•Do not sharpen the cutting blade. Sharpening the blade can cause the blade tip to break off while in use. This can result in severe personal injury. Replace the blade.

•Stop the engine IMMEDIATELY if you feel excessive vibration. Vibration is a sign of trouble. Inspect thoroughly for loose nuts, bolts or damage before continuing. Repair or replace affected parts as necessary.

AFTER USE

•Clean cutting blades with a household cleaner to remove any gum buildup. Oil the blade with machine oil to prevent rust.

•Lock up and store the cutting blade in an appropriate area to protect the blade from unauthorized use or damage.

OTHER SAFETY WARNINGS

•Never store the unit, with fuel in the tank, inside a building where fumes may reach an open flame or spark.

•Allow the engine to cool before storing or transporting. Be sure to secure the unit while transporting.

•Store the unit in a locked up and dry, or high and dry place to prevent unauthorized use or damage. Keep out of the reach of children.

•Never douse or squirt the unit with water or any other liquid. Keep handles dry, clean and free from debris. Clean after each use, see Cleaning and Storage instructions.

•Keep these instructions. Refer to them often and use them to instruct other users. If you loan someone this unit, also loan them these instructions.

SAVE THESE INSTRUCTIONS

WARNING: The operation of any power tool can cause foreign objects to be thrown into your eyes. This can lead to severe eye damage. Before commencing power tool operation, always wear safety glasses or goggles that are marked as meeting ANSI Z87.1-1989 standards, and a full face shield when needed.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents OPERATOR’S Manual Table of Contents IntroductionCalifornia Emission Regulations Spark ArrestorSymbol Meaning Rules for Safe OperationWhile Operating While Operating with Cutting Blade For Service INFORMATION, Call Safety and International SymbolsSymbol Meaning Safety Alert Symbol Unleaded FuelBrushcutters Replace dull blade TRIMMER/BRUSHCUTTER SafetyHOT Surface Warning Choke ControlFuel Cap Know Your UnitApplications Starter RopeHandle Screws Top Clamp Middle Clamp Bottom Clamp Nuts Assembly InstructionsInstalling and Adjusting the J-HANDLE DecalInstalling the Harness Removing and Installing Cutting Attachment ShieldInstall the Cutting Blade Remove the Cutting Attachment ShieldRemove the Cutting Attachment Counterclockwise 1/2 turn CounterclockwiseRemove the Cutting Blade Remove the Cutting Blade and Install the Cutting AttachmentInstall the Cutting Attachment ClockwiseOIL and Fuel Information Using Blended FuelsUsing Fuel Additives OIL and Fuel Mixing InstructionsPartial Choke Position B Full Choke Run STARTING/STOPPING InstructionsOn/Off Stop Control Choke Lever Primer BulbOperating the CLICK-LINK Installing the Cutting Attachment or Add-OnsOperating Instructions System Model 790rHolding the Trimmer Adjusting Trimming Line Length Each time the head is bumped, about 1Tips for Best Trimming Results Using the Cutting Blade Decorative TrimmingCutting Blade Operating Tips Maintenance and Repair Instructions Maintenance ScheduleFrequency Maintenance Required Refer to Outer Spool Spring Inner Reel Bump Knob Line InstallationWinding the Existing Inner Reel Indexing TeethHolding Slots Removing the Air Filter/Muffler Cover Installing a Prewound ReelAIR Filter Maintenance Choke Lever Partial Choke Position B ScrewsCleaning the Air Filter Reinstalling the Air Filter/Muffler CoverAir Filter Adjust Idle Speed Screw Carburetor AdjustmentClean Air Filter Check Fuel Mixture110-120 in.lb .3-13.5 Nm ACCESSORIES/REPLACEMENT PartsReplacing the Spark Plug 020Storage Cleaning and StorageCleaning Long Term StorageTroubleshooting Problem Cause ActionSpecifications EngineDrive Shaft & Cutting Attachment Page Owners Warranty Responsibilities Ryobi Outdoor Products Ryobi Canada INC

780r specifications

The Ryobi 780R is a powerful and reliable gas-powered string trimmer known for its exceptional performance and user-friendly features. Designed for both professionals and homeowners, this tool offers versatility and efficiency for tackling tough trimming jobs around the yard.

One of the standout features of the Ryobi 780R is its robust 30cc 2-cycle engine. This engine provides ample power to handle thick weeds and overgrown grass, ensuring a clean and precise cut with every pass. The lightweight design of the trimmer enhances maneuverability, making it easy to navigate around obstacles such as trees, flower beds, and garden furniture.

The trimmer is equipped with a premium 18-inch cutting swath, allowing for a wider range to be covered in a single pass. This feature can significantly reduce the time required to complete larger trimming tasks. Additionally, the variable speed throttle gives users the flexibility to adjust the cutting power based on the density of the vegetation, offering greater control.

One of the notable technologies in the Ryobi 780R is its Easy Start technology, which simplifies the starting process, reducing the effort required to get the engine running. This is particularly beneficial for users who may struggle with traditional pull-start mechanisms. The trimmer also features an automatic choke system, ensuring optimal engine performance in various conditions.

Another important characteristic is its dual-line feed system. The Ryobi 780R uses a bump head for easy line advancement; simply bump the head on the ground to extend the line as needed. This functionality minimizes downtime and allows users to focus on the task at hand. The dual-line setup also enhances cutting efficiency, making it a great choice for tougher vegetation.

In terms of comfort, the Ryobi 780R incorporates ergonomic handle designs that reduce user fatigue during extended use. The adjustable shaft allows for personalized length settings, catering to users of varying heights, further enhancing comfort and control. With built-in safety features such as a protective shield, users can operate the trimmer with peace of mind.

The Ryobi 780R is not just a powerful trimmer but also a thoughtfully designed tool that combines performance with user convenience. Whether you are maintaining a small garden or handling larger landscaping tasks, this trimmer offers the reliability and efficiency needed to achieve a well-kept lawn. Its blend of innovation and practical features makes it a favored choice among gardening enthusiasts and professionals alike.
Top Page Image Contents