Snapper MCRP215014KWV, MCR5215014KWV Replacing Bearing In Driven Disc Assembly Commercial Models

Page 16

Section 4 - ADJUSTMENTS & REPAIR

4.3.6.Replacing Bearing In Driven Disc Assembly (Commercial Models)

If the driven disc bearing fails, remove the driven disc assembly and replace bearing as follows:

1.Using a small flat blade screwdriver, free the clip from the transfer rod. Then remove the transfer rod from the clip and the speed control rod. Refer to Figure

2.Using needle nose pliers, unhook the drive spring and slide the driven disc assembly off the hex shaft. Refer to Figure 4.12.

3.Remove snap ring that secures driven disc hub to thrust plate. See Figure 4.15.

4.Slide the driven disc hub out of the bearing.

5.Remove the four screws that secure bearing.

6.Remove bearing and replace with new bearing and secure with four retaining screws.

7.Reassemble components in reverse order.

4.Slide the rubber driven disc hub out of the bearing.

5.Drive out existing bearing.

6.Install new bearing and secure to thrust plate with four retaining screws. Tighten screws securely.

7.Reassemble components in reverse order.

INSTALL

NEW

BEARING

SNAP

THRUSTRING PLATE

BEARING

REMOVE

FOUR

MACHINE

SCREWS

SHIM WASHER

DRIVEN DISC HUB

TIGHTEN

THE FOUR

SCREWS

SNAP RINGS

REINSTALL

DRIVEN

DISC

FIGURE 4.16

RUBBER

DRIVENDISC DISC

PLATE

FIGURE 4.15

4.3.7.Replacing Bearing In Driven Disc Assembly (Non-Commercial Models)

IMPORTANT: The bearing, on these “M” series Non- Commercial machines, is staked into the thrust plate. The bearing will have to be driven out with a mallet and a large punch. A new bearing with four retaining screws will have to be purchased to replace existing bearing.

If the driven disc bearing fails, remove the driven disc assembly and replace bearing as follows:

1.Using a small flat blade screwdriver, free the clip from the transfer rod. Then remove the transfer rod from the clip and the speed control rod. Refer to Figure

2.Using needle nose pliers, unhook the drive spring and slide the driven disc assembly off the hex shaft. Refer to Figure 4.12.

3.Remove both snap rings that secure rubber driven disc hub to thrust plate. See Figure 4.16.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Steel Deck Walk Mowers M Model Series Important Safety Instructions Operation Table of Contents Introduction NomenclatureStarting & Operation 2.2.1. Engine & Blade PRE-START Check ListPrimer Models Push & Non Commercial Self-Propelled Handle Height Adjustment Starting & Operation 2.2.2. Engine & BladeChoke ModelsCommercial Only Propelling MowerSwivel Wheel Lock and Unlock Swivel Wheel Models Only Cutting Height AdjustmentRecycling Operation Check Grease Level in Transmission Service After First 5 Hours 3.2.1. Change Engine OILOn Next Storage Procedure Check Mower BladeCheck Engine Drive Belt Check Transmission POLY-V BeltBlade Sharpening Ninja Blade Wear LimitWheel Drive Control Adjustment Driven Disc Service Cleaning Drive Disc & Driven DiscDrive Spring Repair/Replacement Driven Disc AdjustmentReplacing Rubber Driven Disc Ring Commercial Model Replacing Rubber Driven Disc Non-Commercial Model Replacing Bearing In Driven Disc Assembly Commercial Models Belt Service 18AStretch Belt Pulley Position Standard Belt Pulley PositionAdjustments & Repair Troubleshooting Problem Probable Cause Corrective ActionService Performed Each Clean Sponge Element Engine ManualMAINTENANCE/REPLACEMENT Parts 100Year Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Page Page Steel Deck Walk Behind Mowers M Model Series

MCR5215014KWV, EMRP215014B, MRP218014T, MR5014B, MCRP215014KWV specifications

The Snapper MCRP215014KWV, MR5014B, MRP218014T, EMRP215014B, and MCR5215014KWV represent a suite of advanced lawn care and landscaping equipment designed for optimal performance and user experience. These models incorporate cutting-edge technology and engineering to deliver reliability, efficiency, and ease of use for both residential and commercial operators.

One of the standout features of these models is their powerful engines, which provide robust performance and enable them to tackle a vast array of mowing conditions. The engines are designed for durability, ensuring long life and reduced maintenance. The high torque output allows for effective cutting of not just grass but also thicker weeds and tougher vegetation, making them versatile tools for any lawn care enthusiast.

Another significant characteristic of these Snapper models is their superior cutting deck design. The cutting deck is engineered to deliver precise cuts and has the capability to discharge clippings efficiently, leaving a clean and tidy lawn. Some models in the suite feature a three-in-one cutting system that allows for mulching, bagging, or side discharge options, providing users with flexibility based on their needs and preferences.

Ergonomics plays a crucial role in the design of these mowers. The Snapper models come with adjustable handles, allowing users to set their desired height for comfortable operation. Easy-to-reach controls enhance usability, making the mowing process less labor-intensive. A self-propulsion feature is available on select models, enabling effortless maneuvering across diverse terrains and inclines.

Technological advancements are prominently featured in these mowers, with some equipped with advanced ignition systems for reliable starts in varying weather conditions. Certain models also integrate enhanced fuel efficiency technologies, minimizing fuel consumption while maximizing performance.

Safety is not overlooked, with several built-in safety features designed to protect the operator and bystanders during operation. These include blade brake systems, which immediately halt blade activities when the user releases the handle, mitigating risks associated with unintentional injuries.

In conclusion, the Snapper MCRP215014KWV, MR5014B, MRP218014T, EMRP215014B, and MCR5215014KWV models are engineered to meet the demands of modern lawn care. Their combination of powerful engines, versatile cutting options, ergonomic design, and advanced safety features demonstrates Snapper’s commitment to delivering high-quality tools for lawn maintenance and landscaping needs. Whether for residential use or professional landscaping, these models stand out for their performance and reliability.
Top Page Image Contents