Snapper E251023BVE, E281223BVE, E281323BVE, E331523KVE Interlock System, Check Engine

Page 18

Section 3 - MAINTENANCE

3.2.7. INTERLOCK SYSTEM

Check interlock controls for proper function:

The engine MUST NOT start if:

1. Blade Control is “ON” and/or clutch/brake pedal

IMPORTANT: When cover is removed, you are viewing the carburetor side of the air filter, which will appear clean. Remove filter and pre-cleaner for inspection.

is released.

The engine and blades MUST STOP if:

2. The operator leaves the operator position with

Blade Control “ON” and/or clutch/brake pedal is

released.

WARNING

DO NOT operate machine if interlock system is not functioning properly. Contact your SNAPPER dealer immediately for assistance.

3.2.8. REVERSE LOCKOUT MECHANISM

Check function of Reverse Lockout Mechanism with engine off.

1.

Depress and hold blade pedals.

2.

Depress and hold clutch/brake pedal.

AIR CLEANER LATCH

BRIGGS ENGINE SHOWN

AIR CLEANER

COVER

3. Shift lever must not go into reverse.

WARNING

DO NOT operate machine if Reverse Lockout Mechanism is not functioning properly. Contact your SNAPPER dealer immediately for assistance.

3.2.9. LUBRICATION – GREASE FITTINGS

The following components on the Rear Engine Rider are equipped with grease fittings and require periodic lubrication. Apply General Purpose grease (NLGI No.2) with a grease gun.

1.Front Wheel Bearings. Refer to Section “FRONT WHEEL BEARINGS – LUBRICATION”.

2.Rear Axle Bearing. Refer to Section “REAR AXLE BEARING – LUBRICATION”.

3.Mower Blade Spindle. Refer to Section “MOWER BLADE SPINDLE – LUBRICATION”.

3.3SERVICE - EVERY 25 OPERATING HOURS Perform all service required after the first 5 hours of operation. Refer to Section “SERVICE – AFTER 5 HOURS”.

3.3.1.CHECK ENGINE

1.Change engine oil. Refer to Section “CHANGE ENGINE OIL”. Refer to engine owner's manual for oil specification.

2.Change air filter. Pull up and rotate the air cleaner latch to remove cleaner cover. See Figure 3.4.

FIGURE 3.4

3.Refer to engine owner's manual for cleaning and service instructions. Remove and clean engine air pre-cleaner. Remove and replace engine air cleaner. See Figure 3.5. Install pre-cleaner and air cleaner per engine owner’s manual.

BRIGGS ENGINE SHOWN

AIR PRE-

CLEANER

AIR CLEANER

FIGURE 3.5

4.Reinstall air cleaner cover. Insert tabs located at the bottom of the cover into corresponding slots in engine cover. Position cover and engage latch over cover and rotate and push down to lock. IMPORTANT: The tabs on the air cleaner cover must be completely inserted into engine cover or the compartment will not be completely sealed to prevent debris from entering into the carburetor.

18

Image 18
Contents European Rear Engine Riding Mower Series Manual No -5573 I.R /30/03Important Safety Instructions Safe Handling of Gasoline Maintenance Table of Contents Introduction NomenclatureFamiliarization Decals / Symbols Lowest Traction Height CUT Clutch OPERATOR’S Seat Adjustment 2.2.1. Front to Rear Adjustment PRE-START Check ListStarting & Operation Engine Electric Start On NextStarting & Operation Engine Electric StartEngine Manual Start Starting & Operation 2.3.3. Mower Blade Wheel DriveStopping ENGINE, Wheel DRIVE, Blade 2.4.1. Engine Mower BladeCutting Height Adjustment Stopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park BrakeDo not park machine on slopes Reverse Lockout Mechanism Service After First 5 Hours Change Engine OIL Service Engine AIR Cleaner Check Mower BladeService After First 5 Hours 3.2.4. Check Blade Drive Belt Service Brake / Park BrakeBlade Brake Interlock System Lubrication Grease FittingsCheck Engine Do not Overfill Battery Fluid LevelClean Mower Deck Mower Deck LevelnessLeft Rear Axle Bearing Grease Fitting Every TWO Years Service AnnuallyFuel Filter Storage OUT of SeasonEngine Adjustments & Repair Blade Brake AdjustmentClearance Mower Drive Belt Adjustment for 25/28 Decks only Mower Deck Adjustment Brake Cable Chain Case Depress Loosen CLUTCH/BRAKE Mower Blade Replacement 4.4.1. Blade Wear Limits Blade SharpeningBelt Removal Blade Drive Belt ReplacementBelt Replacement 25/28 DecksBattery Battery Removal Battery InstallationNEW Battery Preparation 1. Remove battery from carton Battery ServiceBattery Storage Battery TestingSnapper Rear Engine Rider Accessories Problem Probable Cause Corrective Action StopCutting Grass Loss Of TractionBlades Not Cutting ImproperlySubject Service Reference To be Performed PagesMAINTENANCE/REPLACEMENT Parts Maintenance Parts Year Limited Warranty Disclaimer of WarrantyPage Manual No -5573 I.R /30/03