Snapper 421620BVE Starting & Operation 2.3.3. Mower Blade, Wheel Drive

Page 9

Section 2 - OPERATING INSTRUCTIONS

WARNING

Once blade is disengaged, it should come to a complete stop in 3 seconds or less. If the blade continues to rotate after 3 seconds, the blade brake must be adjusted. Refer to Section “BLADE BRAKE ADJUSTMENT” for adjustment procedures or return machine to an authorized SNAPPER dealer for adjustment. DO NOT CONTINUE to operate machine until blade brake is adjusted and functioning properly.

2.3STARTING & OPERATION 2.3.3. MOWER BLADE

1.With engine running, move engine speed control to the “FAST” position.

2.Move blade lever forward to the “ON” position, then depress blade pedals to hold blade lever in the “ON” position. See Figure 2.10.

IMPORTANT: You cannot engage the blade lever if the blade pedal is depressed first.

RAISE BLADE

LEVER TO “ON”

BLADE LEVER

SHOWN DISENGAGED

DEPRESS BLADE PEDALS

FIGURE 2.10

2.3.4. WHEEL DRIVE

1.With engine running, adjust engine speed control to “FAST” position.

2.Depress clutch/brake pedal. See Figure 2.11.

3.Place transmission shift lever in the notch for 1st speed. See Figure 2.12.

4.Release clutch/brake pedal to begin desired ground speed.

5.During forward motion, the transmission shift lever may be placed in any desired forward speed without depressing the clutch/brake pedal.

NOTE: For best cutting results, move the transmission shift lever into a slow forward speed and the engine speed control to a fast position. This combination will allow the mower blades to lift the grass while cutting smoothly and evenly.

WARNING

DO NOT operate blades in reverse. STOP BLADES. LOOK and SEE behind and down for children, pets and hazards before and while backing.

DEPRESS

CLUTCH/BRAKE

PEDAL

FIGURE 2.11

MOVE TRANSMISSION

SHIFT LEVER TO

DESIRED SPEED

FIGURE 2.12

9

Image 9
Contents Manual No -3543 I.R /29/00 Rear Engine Riding Mower SeriesImportant Safety Instructions Operation Table of Contents Control Panel IntroductionNomenclature PRE-START Check List OPERATOR’S Seat Adjustment Front to Rear AdjustmentOn Next Starting & Operation Engine Electric StartStarting & Operation Engine Electric StartEngine Manual Start Wheel Drive Starting & Operation 2.3.3. Mower BladeMower Blade Stopping ENGINE, Wheel DRIVE, Blade 2.4.1. EngineCutting Height Adjustment Stopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park BrakeDo not park the machine on slopes Reverse Lockout Mechanism Override Reverse Lockout MechanismService Engine AIR Cleaner Check Mower Blade Service After First 5 Hours Change Engine OILAdjusting Mower Blade Check blade for straightness. Refer to SectionService Brake / Park Brake Service After First 5 Hours 3.2.4. Check Blade Drive BeltTOP View of Belt Routing Blade BrakeBattery Fluid Level Service Every 25 Operating HoursClean Mower Deck Lubrication Grease FittingsService Annually EngineFuel Filter Every TWO Years Storage OUT of SeasonRemoving Fuel Tank Engine Adjustments & Repair Mower Drive Belt AdjustmentBlade Brake Adjustment Side To Side Levelness Mower Deck AdjustmentFront to Rear Levelness Wheel Brake Adjustment Mower Blade Replacement 4.4.1. Blade Wear Limits Blade Drive Belt Replacement Blade SharpeningBelt Removal Belt Replacement Battery Installation Battery Battery RemovalBattery Storage Battery ServiceNEW Battery Preparation 1. Remove battery from carton Battery TestingSnapper Rear Engine Rider Accessories Stop Problem Probable Cause Corrective ActionBlades Not Cutting Loss Of TractionCutting Grass ImproperlyTo be Performed Pages Subject Service ReferenceDisclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Rear Engine Riding Mower Series