Snapper 2167517BV, P2167517BV, P2167517BVE, WP2167517BV important safety instructions

Page 16

Section 4 - REPAIR & ADJUSTMENTS

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

4.3.4.Replacing Rubber Driven Disc (Continued from previous page)

2.Using needle nose pliers, unhook the drive spring and slide the driven disc assembly off the hex shaft. See Figure 4.12.

3.Remove the two snap rings which secure the rubber driven disc to the driven disc assembly. See Figure 4.13.

4.Install new rubber driven disc onto driven disc assembly with retaining rings.

5.Reverse above procedures for reassembly and installation of driven disc assembly.

4.3.5.Replacing Bearing In Driven Disc Assembly IMPORTANT: The bearing on these machines is staked into the thrust plate. The bearing will have to be driven out with a mallet and a large punch. A new bearing with four retaining screws will have to be purchased to replace existing bearing.

If the driven disc bearing requires replacement, remove the driven disc assembly and replace bearing as follows:

1. Using a small flat blade screwdriver, free the clip from the transfer rod. Then remove the transfer rod from the clip and the speed control rod. See Figure 4.11.

2. Using needle nose pliers, unhook the drive spring and slide the driven disc assembly off the hex shaft. See Figure 4.12.

3. Remove both snap rings that secure rubber driven disc hub to thrust plate. See Figure 4.13.

4. Slide the rubber driven disc hub out of the bearing.

5. Drive out existing bearing.

6. Install new bearing and secure to thrust plate with four retaining screws. Tighten screws securely. 7. Reassemble components in reverse order.

DRIVE DISC

ASSEMBLY

INSTALL NEW

DRIVEN DISC

SNAP

RINGS

FIGURE 4.12

FIGURE 4.13

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Steel Deck Walk Mowers Series Model Number ExplanationImportant Safety Instructions Operation Table of Contents Introduction NomenclaturePRE-START Check List Starting & Operation 2.2.1. Engine & BladeRecoil Start Models Engine & Blade Electric Start ModelsCutting Height Adjustment Handle Height AdjustmentPropelling Mower Self Propelled Models OnlyInstallation of Grass BAG Adapter Installation of Grass BAGRecycling Operation On NextInstallation of Recycling Cover Optional Accessory on Some ModelsMaintenance Service After First 5 Hours 3.2.1. Change Engine OILService Annually Storage ProcedureCheck Mower Blade Check Engine Drive BeltBlade Sharpening Mower Blade Replacement 4.1.1. Standard Blade Wear Limit1.A. Ninja Blade Wear Limit Wheel Drive Control Adjustment Driven and Drive Disc Service Driven Disc AdjustmentCleaning Drive Disc & Driven Disc Drive Spring Repair/ReplacementReplacing Rubber Driven Disc Drive Disc Assembly Install NEW Driven Disc Snap Rings Engine Drive Belt Replacement Stretch Type Belts Belt ServicePulley Position Battery Service 4.5.1. Battery Service Battery StorageBattery Testing NEW Battery PreparationTroubleshooting Problem Probable Cause Corrective ActionService Performed Each Clean Sponge Element Engine ManualMAINTENANCE/REPLACEMENT Parts 100Year Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Page Page Page Steel Deck Walk Behind Mowers Series

216517B, 2167517BV, R215517HC, R2167517BV, P215517HC, P216517B, P216517BV, P216517BVE, P217017BV, P217017BVE, RP215517HC, RP216751BV, RP217017BV, RP2167517BVE, RP217017BVE, WP2167517BV, WP216517BV, WRP216517BE, FRP2167517BV, EP2167517BV, EP217017BV, ERP21, 2167517BV, P2167517BV, P2167517BVE, WP2167517BV specifications

Snapper is a well-known brand in the power equipment industry, particularly recognized for its line of high-quality lawn mowers and outdoor power tools. Among its extensive product range, the Snapper model numbers 216517B, 2167517BV, R215517HC, R2167517BV, P215517HC, P216517B, P216517BV, P216517BVE, P217017BV, P217017BVE, RP215517HC, RP216751BV, RP217017BV, RP2167517BVE, RP217017BVE, WP2167517BV, WP216517BV, WRP216517BE, FRP2167517BV, EP2167517BV, EP217017BV, and ERP21,2167517BV all stand out for their performance and reliability.

These models are designed with advanced engines that deliver powerful performance, enabling users to tackle even the toughest mowing jobs. The cutting deck technology is engineered for precision and efficiency, contributing to clean and even cuts. Many of these models feature a robust steel construction, ensuring durability and longevity for the equipment.

Some models offer various cutting heights, allowing for customizable lawn care, catering to different grass types and user preferences. Additionally, Snapper mowers are equipped with an ergonomic handle design, ensuring comfort during use while reducing fatigue. The availability of multiple speed settings enhances user control and convenience.

Another significant feature is the ease of maintenance; many of the Snapper models are designed for straightforward access to blades and engines, making routine care less cumbersome. The introduction of innovations such as electric start options in certain models enhances user-friendliness, appealing to both seasoned landscapers and new users.

Snapper also integrates eco-friendly technologies into their products, ensuring emissions are kept to a minimum without compromising power. Models like the P216517BVE and WP2167517BV exemplify this balance of performance and sustainability.

With a commitment to quality and innovation, Snapper continues to provide versatile, reliable, and efficient mowing solutions suitable for both residential and commercial applications. Whether it's the robust R2167517BV or the user-friendly P215517HC, Snapper’s extensive lineup is tailored to meet a diverse range of lawn care needs, making them a go-to choice for outdoor power equipment enthusiasts.
Top Page Image Contents