Snapper NP216012, EP216012 Service After First 5 Hours 3.2.1. Change Engine OIL, On Next

Page 9

Section 3 - MAINTENANCE

3.1INTRODUCTION

To retain the quality of the mower, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular mower, always mention model and serial number.

3.2SERVICE - AFTER FIRST 5 HOURS 3.2.1. CHANGE ENGINE OIL

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

1.Refer to Engine Manual for proper oil specifications and procedures.

2.For simplest/cleanest oil change, loosen lower handle wing nuts and stand mower up on lower handle as shown in Figure 3.1. Drain oil through dipstick tube into a container.

FIGURE 3.1

3.2.2.CHECK GREASE LEVEL IN TRANSMISSION 1. Remove transmission fill plug. Roll machine forward or backward while looking down into plug hole.

2. If liquid grease IS NOT visible on the input gear (the small gear below the plug hole), add an amount, to cover gear, of Snapper “00” grease. See Figure 3.2.

FILL PLUG

FIGURE 3.2

NOTE: Snapper “00” Grease (Part No. 29443)- is available at your SNAPPER dealer.

(Continued on Next Page)

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Steel Deck Walk Mowers Series 12 Important Safety Instructions Operation Table of Contents Nomenclature IntroductionPRE-START Check List Starting & Operation 2.2.1. Engine & BladePrimer Models Handle Height Adjustment Cutting Height AdjustmentPropelling Mower StoppingInstallation of Grass Catcher Adjusting Front Deck BaffleRecycling Operation Models with an F prefix in model numberOn Next Service After First 5 Hours 3.2.1. Change Engine OILStorage Procedure Service AnnuallyCheck Mower Blade Check Engine Drive BeltMower Blade Replacement 4.1.1. Standard Blade Wear Limit Blade Sharpening1A. Ninja Blade Wear Limit Wheel Drive Control Adjustment Driven Disc Adjustment Driven Disc ServiceCleaning Drive Disc & Driven Disc Drive Spring Repair/ReplacementReplacing Rubber Driven Disc Ring Replacing Rubber Driven Disc Ring From Previous Belt Service Driven Idler Pulley Differential Bracket Problem Probable Cause Corrective Action TroubleshootingClean Sponge Element Engine Manual Service Performed EachMAINTENANCE/REPLACEMENT Parts 100Disclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Page Page Page Steel Deck Walk Behind Mowers Series 12
Related manuals
Manual 52 pages 34.22 Kb

215012, 215014, R215012, N215012, NR215012, FR215012, FR215014, P216012, EP216012, NP216012, RP215012, RP216012, RP215012T2, FRP216012, NRP215012, NFRP216012, 215012, 215014, R215012, N21512, NR215012, FR215012, FR215014, P216012, EP216012, NP216012, RP215012, RP216012, RP215012T2, FRP216012, NRP215012, NFRP216012, EP216012, NP216012, P216012, P216512BV, WP221651BV specifications

The Snapper FR215012, NFR215012, P216012, P216512BV, WP221651BV, NP216012, EP216012, and their various counterparts form a comprehensive range of advanced outdoor power equipment primarily focused on mowing and landscaping tasks. These models have garnered positive feedback for their performance, reliability, and innovative features tailored for both residential and commercial use.

The Snapper FR215012 series is renowned for its efficient engine technology, which utilizes a robust Briggs & Stratton engine, delivering significant power and ensuring longevity. The engines are designed for high torque operation, which is essential for cutting through thick grass or tackling uneven terrains. The ergonomic design of the handle allows for comfortable usage over extended periods, significantly reducing operator fatigue.

One notable feature across these models is the SmartSpeed technology, which enables the operator to easily switch between ground speeds without the need to adjust the throttle. This is particularly advantageous when performing various tasks such as trimming, mowing, and navigating around obstacles, providing users with enhanced maneuverability and control.

The cutting decks on Snapper units, including the P216012 and P216512BV, are engineered with precision to deliver clean, even cuts. They feature adjustable cutting heights, allowing for customization based on grass type and desired finish. The decks are often constructed from durable materials that resist rust and corrosion, ensuring that the equipment has a long lifespan.

In addition to cutting efficiency, the Snapper models are designed with user-friendly maintenance features. Easy-access oil drains, tool-less filter access, and straightforward blade replacement mechanisms contribute significantly to efficient upkeep. Furthermore, safety features such as operator presence control ensure that the mower operates only when the user is actively engaged, minimizing the risk of accidents.

Overall, the Snapper FR215012 series and its variants are characterized by their blend of performance, reliability, and user-focused features. They cater to a wide array of lawn care needs while maintaining a commitment to safety and ease of operation. Whether for residential lawns or professional landscaping operations, these models offer the versatility and power required to achieve exceptional results. With ongoing advancements in lawn care technology, Snapper continues to position itself as a dependable choice for those in need of high-quality outdoor power equipment.
Top Page Image Contents