Snapper 2167520B (7800428) Installing the Discharge Deflector, Installing the Grass Bag Adapter

Page 10
Installing the Discharge Deflector

Operation (Continued)

Operation

!

WARNING

!

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

Installing the Discharge Deflector

1.Remove the recycling cover. Refer to the Section entitled “Recycling Operation”.

2.Install the deflector (A, Figure 10) to the deck in place of the recycling cover, making sure that:

Figure 10: Installing the discharge deflector The front hole (B) on the outside front of the deflector fits over the stud where the front of the recycling cover was originally secured

Installing the Grass Bag Adapter The slot (C) on top of the deflector slips under the restraining nut on top of the deck (under the right front corner of the engine)

Figure 11: Installing the grass bag adapter The slot (D) on the inside rear of the deflector slips onto the stud behind the rear of the discharge opening, where the rear of the recycling cover was originally secured.

3.Install the internal/external tooth lock washers and knob nuts onto the studs and tighten securely.

C

B

 

D

 

 

A

Figure 10: Installing the discharge deflector

Installing the Grass Bag Adapter

(Optional Accessory on Some Models)

1.Remove the recycling cover. Refer to the Section entitled “Recycling Operation”.

2.Install the adapter (A, Figure 11) to the deck in place of the recycling cover, making sure that:

Manual background The front hole (B) on the outside front of the adapter fits over the stud where the front of the recycling cover was originally secured

Manual background The slot (C) on top of the adapter slips under the restraining nut on top of the deck (under the right front corner of the engine)

Manual background The slot (D) on the rear of the adapter slips onto the stud behind the rear of the discharge opening, where the rear of the recycling cover was originally secured.

3.Install the internal/external tooth lock washers and knob nuts onto the studs and tighten securely.

4.Route the recoil rope around the outside of the rope guide pulley (E).

Note: The recoil rope may need to be slackened. Refer to the section entitled “Handle Assembly”.

E

C

B

D

A

Figure 11: Installing the grass bag adapter

!

WARNING

!

DO NOT operate without entire Grass Catcher or guard in place. Grass Catcher components are subject to deterioration during normal use. Inspect frequently and replace worn or damaged components immediately.

8

www.snapper.com

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Models 21” STEEL DECK WALK MOWERS SERIESSafety Instructions & Operators Manual for RP217020BDV 7800424 RP2187520BV RP2187520BVE 7800427 2167520BEngine PRODUCT REGISTRATIONDate of Purchase Retailer Retailers Phone Number Equipment Snapper at P.O. Box 1379, McDonough, GeorgiaFeatures and Controls Operation Table of ContentsOperator Safety MaintenanceSlope Operation Important Operator Safety InstructionsProtection for Children PreparationSafe Handling of Gasoline Continued From Previous Page Important Operator Safety Instructions ContinuedMaintenance and Storage OperationFeatures and Controls Features and ControlsStarting and Operation OperationPre-Start Check List Engine and Blade Briggs Quantum and Intek Series EnginesStopping Handle Height AdjustmentOperation Continued Propelling the Mower Self-Propelled Models OnlyRemoving the Recycling Cover Cutting Height AdjustmentRecycling Operation Figure 7 Adjusting cutting heightFigure 10 Installing the discharge deflector Installing the Discharge DeflectorInstalling the Grass Bag Adapter Figure 11 Installing the grass bag adapterIMPORTANT Install the grass bag as a safeguard Installing the Recycling PlugInstalling the Grass Bag Figure 12 Installing the recycling plugService - After First 5 Hours MaintenanceMaintenance - Introduction Check Grease Level in TransmissionStorage Procedure Maintenance ContinuedService - Periodic Check Mower BladeNinja Blade Wear Limit Mower Blade ReplacementStandard Blade Wear Limit Blade SharpeningFigure 22 Wheel drive control adjustment Blade Sharpening ContinuedWheel Drive Control Adjustment Self-Propelled Models Only Figure 21 Sharpening the mower bladeDrive Spring Repair/Replacement Driven and Drive Disc ServiceCleaning Drive Disc & Driven Disc Driven Disc AdjustmentFigure 26 Adjusting the driven disc Driven Disc Adjustment ContinuedDriven Disc Replacement Figure 27 Proper driven disc adjustmentFigure 29 Removing the driven disc assembly Driven Disc Replacement ContinuedDriven Disc Bearing Replacement Figure 30 Replacing the driven discReplacing the Bearing On the Pulley End Of the Hex Shaft Belt ServiceEngine Drive Belt Replacement Stretch Type Belts Figure 32 Engine drive belt routingA B C D E F G Engine Drive Belt Replacement Stretch Type Belts - ContinuedTransmission Poly-V Belt Replacement Figure 33 Removing the drive discBattery Service Battery ServiceNew Battery Preparation Battery StorageService Schedule Maintenance/Replacement PartsPROBABLE CAUSE TroubleshootingCORRECTIVE ACTION DISCLAIMER OF WARRANTY 2 YEAR LIMITED WARRANTYWarranties Page Page Page Part Number Product SpecificationsCommon Service Parts Snapper Products
Top Page Image Contents