Snapper P216518B important safety instructions Installation of Grass BAG Adapter, 10a

Page 9

Section 2 -OPERATING INSTRUCTIONS

2.Set all wheels at the same cutting height. The highest cutting position is Notch 6. The lowest cutting position is Notch 1. See Figures 2.8 & 2.9.

STEP la (Kawasaki only): Attach Bag Adapter Standoff between rope guide pulley assembly and engine recoil. See Figure 2.10a.

LATCH

Fq

A. Remove right rear bolt from engine recoil cover. B. Remove torx screw and nut securing rope guide pulley to bracket on bag adapter.

C. Lay standoff between bolt holes in engine recoil

POSITION

CUTTING HEIGHT SETTINGS

FIGURE 2.9

2.6INSTALLATION of GRASS BAG ADAPTER

cover and bag adapter pulley bracket. NOTE: position standoff so that bent end is toward engine recoil cover.

D. Flip pulley over so that flange of steel bushing is under pulley. (The bushing wilt act as a washer between the pulley and standoff.)

E. Reassemble pulley to bag adapter, and reinstall bolt into recoil cover. Tighten all hardware securely.

BOLTSTANDOFF

ROPE GUIDE PULLEY

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

STEP 1: Install the grass bag adapter and secure to the side and top of the deck with the two nuts provided on the machine. Slot in front edge of adapter must be under nut located on top of deck. See Figure 2.10.

!

SECURE ADAPTER

TO DECK WITH NUTS

SECURE

WITH NUTS

ADAPTER

FIGURE 2.10

FIGURE 2.10a

STEP 2: Route recoil rope around recoil rope pulley on

bag adapter. See Figure 2.10a. NOTE: Pulling Blade control against upper handle will allow extra recoil slack.

2.7 INSTALLATION of RECYCLING PLUG

(Optional Accessory on Some Models)

STEP 1: Once adapter has been installed, recycling may be desired. Insert recycling plug completely and securely into adapter. See Figure 2.11. Install grass bag as a safeguard.

 

INSERT RECYCLING PLUG

PLUG

COMPLETELY

AND SECURELY

 

INTO ADAPTER.

INSTALL

 

GRASS BAG.

 

FIGURE 2.11

STEP 2: Refer to Section "OPERATING INSTRUCTIONS - RECYCLING OPERATION".

Image 9
Contents Model Number Explanation Steel Deck Walk Mowers SeriesImportant Safety Instructions Operation Important Safety Instructions Table of Contents Briggs Engine Speed Control Kawasaki Engine Speed ControlIntroduction Nomenclature PRE-START Check List Cutting Height AdjustmentStarting & Operation Engine & Blade Briggs EngineCutting Height Adjustment Handle Height AdjustmentStarting & Operation Stopping Propelling Mower10a Installation of Grass BAG AdapterRemoving and Dumping Grass Catcher Slide Closure Type Installation of Grass CatcherRecycling Operation Service After First 5 Hours 3.2.1. Change Engine OIL IntroductionCheck Grease Level in Transmission Storage Procedure SERVICE-ANNUALLYInjury Check Mower BladeWearlimit Mower Blade Replacement Standard Blade Wear LimitBlade Sharpening BladeCUTT,NGEDGE 22 8o Wheel Drive Control AdjustmentCleaning Drive Disc & Driven Disc Driven and Drive Disc ServiceDrive Spring Repair/Replacement Driven Disc AdjustmentDriven Disc Adjustment From PreviousOn Next Replacing Rubber Driven Disc Install NEW Driven Disc Remove Belt Service Engine Drive Belt Replacement Stretch Type BeltsOn Next Transmission Poly-V Belt Replacement Pulley PositionDeckbracket Battery Service Battery Service NEW Battery PreparationBattery Testing Syringe Hydrometer Digital VoltmeterCorrective Action TroubleshootingService Performed Each USE HRS MAINTENANCE/REPLACEMENT PartsHRS HRS HRS Season Disclaimer of Warranty Year Limited WarrantyHow dirt can Cost YOU Money Check OIL Level Before Each START-UP Bpark plug Throttle control 10, Blade Starting Check USTSnapper Product Registration Form Page Page Steel Deck Walk Behind Mowers Series
Related manuals
Manual 44 pages 34.88 Kb