Snapper P216012TV, FRP216012TV, EFRP216012TV, EFRP216512TV, EFRP216516TV Belt Service

Page 15

Section 4 - REPAIR & ADJUSTMENTS

WARNING

Before attempting any adjustments or repairs, STOP the engine, remove the spark plug wire from the spark plug and secure wire away from plug.

4.3.5. Replacing Bearing In Driven Disc

If the driven disc bearing fails, remove the driven disc assembly and replace bearing as follows:

1.Remove snap ring. See Figure 4.14.

THRUST

SHIM

PLATE

WASHER

 

SNAP

 

RING

BEARING

 

REMOVE FOUR

 

MACHINE SCREWS

 

 

DRIVEN

 

DISC HUB

DRIVEN DISC

RUBBER

DISC

PLATE

 

 

 

FIGURE 4.14

2.Slide the hub assembly out of the bearing.

3.Remove the four screws.

4.Remove bearing and replace with new bearing.

5.Reassemble components in reverse order.

4.3.6.Replacement Of Bearing On Pulley End Of Hex

Shaft

To replace the bearing on the pulley end of the hex shaft, proceed as follows:

BALL BEARING

“O” RING

3/8”

LOCK NUT

BALL BEARING

HOLDER

FIGURE 4.15

4.4.BELT SERVICE

On self-propelled mowers, the engine belt transmits power from engine to drive disc. The drive disc powers the poly-v belt which engages the transmission that powers the rear wheels. Should these belts become worn, they could cause slippage which would impair mower performance. The condition of the engine belt and poly-v belt should be checked after every 25 hours of mower operation.

4.4.1.Engine Drive Belt Replacement 1. Empty the fuel tank.

2. Unhook the idler spring from the right rear wheel bracket. See Figures 4.16.

1.

Hold the hex shaft with an adjustable wrench

held next to the pulley.

2.

Remove the 3/8” hex lock nut which is located

on the outside of the right wheel bracket. See Figure

4.15.

3.

Remove holder, O-ring and bearing.

4.

Install new bearing.

5.

Carefully install new O-ring over the outside of the

new bearing.

6.

Install bearing holder and secure with screws.

RIGHT REAR

WHEEL BRACKET

IDLER

SLOT INARM DECK

IDLER SPRING

7. Install 3/8” hex lock nut.

DRIVE DISC

DRIVE BELT

ENGINE DRIVE PULLEY

TOP VIEW OF ENGINE BELT

FIGURE 4.16

15

Image 15
Contents Steel Deck Walk Mowers Series 12 Important Safety Instructions Maintenance and Storage Table of Contents Nomenclature IntroductionStarting & Operation 2.2.1. Engine & Blade PRE-START Check ListStopping Cutting Height AdjustmentHandle Height Adjustment Propelling MowerModels with an F prefix in model number Example FR215012 Adjusting Front Deck BaffleInstallation of Grass Catcher Recycling OperationOn Next MaintenanceCheck Transmission POLY-V Belt Storage ProcedureCheck Mower Blade Check Engine Drive BeltBlade Sharpening 1A. Ninja Blade Wear LimitDriven Disc Service Wheel Drive Control AdjustmentCleaning Drive Disc & Driven Disc Drive Spring Repair/ReplacementDriven Disc Adjustment Replacing Driven Disc Rubber Ring Install 3/8 hex lock nut Replacement Of Bearing On Pulley End Of Hex ShaftBelt Service Engine Drive Belt Replacement 1. Empty the fuel tankLockwasher Problem Probable Cause Corrective Action TroubleshootingUSE HRS Season Service Performed EachClean Sponge Element Engine Manual 100Disclaimer of Warranty Year Limited WarrantyPrimary Maintenance Cost YOU Money Distorted valve guides Sticking Valves Grass & leaves cleaned away Service Notes Steel Deck Walk Mowers Series