Snapper SGV13321KW Deck Belt Adjustment & Replacement, Cutting Deck Adjustment

Page 20

SECTION 6 – ADJUSTMENTS & REPAIRS

WARNING

DO NOT attempt any maintenance, adjustments or service with the engine running. Stop engine. Stop blades. Lock Traction Levers. Remove key. Disconnect spark plug wires from spark plugs and secure wires away from spark plugs. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine.

6.6.2. CUTTING DECK ADJUSTMENT

Cutting height can be adjusted by raising or lowering the Cutting Deck, via Front Caster and Rear Axle adjustments:

1.FRONT CASTER ADJUSTMENT: Each Caster Wheel Assembly has five (5) 1/2” and two (2) 1/4” spacers positioned on the caster shaft. By removing retainer pin, and repositioning spacers above or below Caster Support Tube, the spacers will raise or lower cutting height in 1/2” increments. See Figure 6.8. NOTE: For clearance purposes, one 1/4" spacer must remain below caster support tube.

 

REMOVE

 

RETAINER PIN

REPOSITION

CASTER

SPACERS TO

SUPPORT TUBE

ADJUST DECK

 

HEIGHT

 

SLIDE

NOTE: THOSE SPACERS

REMOVED FROM

CASTER

BOTTOM OF CASTER

SHAFT

SHOULD BE

OUT

REINSTALLED AT TOP

 

BEFORE INSERTING

 

RETAINER PIN.

 

FIGURE 6.8

NOTE: Rear axle must be adjusted in conjunction with front casters to achieve correct cutting height adjustment.

2.REAR AXLE ADJUSTMENT: Position a floor jack beneath rear of mower and raise mower. Loosen axle bolts and adjust axle assembly up or down to correspond with front caster adjustment. See Figure

6.9.NOTE: When adjusting axle make sure that rear of cutting deck is 1/4" higher than front.

LOOSEN

BOLTS

ADJUST

AXLE

FIGURE 6.9

NOTE: Front casters must be adjusted in conjunction with rear axle to achieve correct cutting height adjustment.

NOTE: Traction rods may need to be adjusted after cutting height adjustment is complete.

6.7 DECK BELT ADJUSTMENT & REPLACEMENT

NOTE: For belt adjustment, proceed directly to step 5.

1.Remove nut securing deck idler tensioning rod to rod bracket, and slide rod out from bracket. See Figure 6.10.

2.Remove loosened belt from around blade spindle pulleys, idler pulley and clutch pulley.

3.Install new belt, using same pulley routing. See Figure 6.10.

4.Reinsert tensioning rod into rod bracket, and secure with nut removed in previous step.

5.Adjust belt tension by tightening or loosening tensioning rod nut. Belt should have 10 lbs. pressure with a 3/8” deflection.

ROUTE AROUND

CLUTCH

TENSIONING

ROD NUT

CHECK

TENSION HERE

FIGURE 6.10

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents PRO Series Walk Behind Mower Model Number ExplanationImportant Safety Instructions Protection for ChildrenSlope Operation PreparationSafe Handling of Gasoline OperationMaintenance Table of Contents Nomenclature FamiliarizationIntroduction Decal Identification Dashboard OverlayDecal Identification Operating Instructions IMPORTANT! Before OperatingControls & Their Functions Traction LeversKEY Switch Blade Clutch SwitchEngine Speed & Choke Control Transmission Shift LeverStarting Engine Deck Belt Adjustment & ReplacementPRE-START Check List Machine Movement Forward MotionTurning and Braking Reverse MotionMowing and Turning on Hillsides Cutting Blade OperationStopping Machine Troubleshooting Engine TroubleshootingMower Troubleshooting Symptom Problem SolutionMower Troubleshooting Transmission TroubleshootingMaintenance General Maintenance ScheduleSafety Interlock System Check Hours Procedure CommentsAdjustments & Repairs Lower Traction ROD AdjustmentUpper Traction ROD Adjustment Traction Idler Spring AdjustmentHandle Height Adjustment Cutting Height AdjustmentTransmission Shift Indicator Adjustment Cutting Blade AdjustmentDeck Belt Adjustment & Replacement Cutting Deck AdjustmentTransmission Belt Replacement & Adjustment Traction Belt ReplacementOPC Adjustment Replacement PartsTransmission Parts & Service Blade Removal and Sharpening Cutting Blade ServiceStandard Replacement Blade Electrical Year Limited Warranty Disclaimer of WarrantySnapper Product Registration Form Primary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Page PRO Series Walk Behind Mower

SGV13321KW specifications

The Snapper SGV13321KW is a powerful and versatile lawn mower that has garnered attention for its robust performance and user-friendly features. Designed for homeowners who seek efficiency in lawn care, this model stands out in the crowded market by offering an impressive combination of power, durability, and convenience.

One of the most notable features of the SGV13321KW is its 13.5 gross torque OHV engine. This engine provides ample power to tackle even the thickest grass and challenging terrain, ensuring a clean cut every time. Coupled with a 21-inch steel cutting deck, the mower allows for a wider cutting path, which means fewer passes are required to achieve a manicured lawn. The cutting height is adjustable, offering six different positions from 1.25 inches to 4 inches, allowing users to customize the lawn’s appearance per their specific needs.

The Snapper SGV13321KW incorporates the innovative Ready Start technology, which ensures easy starting without the need for a primer. This feature simplifies the starting process, making it accessible for all users, regardless of their experience level with lawn mowers. Moreover, the mower’s self-propelled drive system offers varying speeds to accommodate different mowing conditions, enhancing user comfort and control.

Durability is a hallmark of the SGV13321KW, as evidenced by its robust construction. The steel deck is not only designed to withstand the rigors of frequent use but also offers a rust-resistant surface for longevity. This is complemented by the mower's foldable handle, which aids in storage and transport, making it a convenient option for those with limited space.

The Snapper SGV13321KW also features an easy-to-use grass bag that is spacious enough to minimize the frequency of emptying. The rear discharge capability allows for effortless grass clipping management, contributing to a cleaner mowing experience. Additionally, the mower's design emphasizes ease of maintenance, with easy access to maintenance points and a user-friendly oil change system.

In conclusion, the Snapper SGV13321KW is a reliable lawn mower that appeals to both beginner and experienced gardeners. Its power, ease of use, adjustable features, and durable construction make it an excellent addition to any lawn care toolkit. With its focus on user convenience and effective performance, the SGV13321KW is well-suited to meet the diverse needs of homeowners seeking to maintain a beautiful and healthy lawn.
Top Page Image Contents