Snapper YZ18336BVE, YZ18386BVE Operating Instructions, PRE-START Check List

Page 7

Section 2 - OPERATING INSTRUCTIONS

2.1PRE-START CHECK LIST

Make the following checks and perform the service required before each start-up.

2.1.1.Check tires and add or release air as needed to bring pressure to 12 P.S.I. in front and 12 P.S.I. in rear tires.

2.1.2.Check guards, deflectors and covers to make sure all are in place and securely tightened.

2.1.3.Check engine oil and add oil as needed to bring level up to the FULL mark. Refer to engine owner’s manual for oil specifications. See Figure 2.1.

ENGINE OIL DIPSTICK

SAFE LEVEL

AREA

FIGURE 2.1

2.1.4.Check Blade switch to insure it works freely. Switch is pulled “OUT” into the “ON” position for blade engagement or pushed back “IN” into the “OFF” position for blade disengagement. See Figure 2.2. IMPORTANT: Blade rotation must stop in 5 seconds or less after moving blade switch to “OFF”. Refer to Section “Blade Brake Adjustment”.

PULL “OUT”

TO ENGAGE

BLADE

SWITCH

PUSH “IN” TO

DISENGAGE

FIGURE 2.2

2.1.5.Clean exterior surfaces of cutting deck and engine of any accumulation of dirt, grass, oil, etc. Keep engine air intake screen and cooling fins clear at all times.

2.1.6.Add fuel to tank of the SCRAMBLER outside where fumes can safely dissipate. Refer to engine owner’s manual for fuel specifications. Make sure fuel filler cap is tight and vent is open after refueling. See Figure 2.3. Open fuel valve located in fuel line.

FUEL FILLER CAP

WITH VENT.

TIGHTEN CAP AND

OPEN VENT AFTER

REFUELING.

FIGURE 2.3

IMPORTANT: To roll the machine without the engine running, pressure within the hydraulic pumps must be released. Tilt seat up and move control lever down to release pressure. NOTE: Control lever must be in the “UP” position to drive machine. See Figure 2.4.

DO NOT USE CONTROL TO RELEASE PRESSURE AND COAST DOWN SLOPES. RELEASE PRESSURE ONLY WHEN MACHINEMOTIONCANBECONTROLLEDANDENGINEOFF.

MOVE CONTROL

LEVER UP TO

DRIVE MACHINE

CONTROL

LEVER

BATTERY

MOVE CONTROL LEVER

DOWN TO ROLL

MACHINE

FIGURE 2.4

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Model Number Explanation ScramblerFrom Previous Column Protection for ChildrenProtection Against Tipovers PreparationOperation Safe Handling of GasolineTowing MaintenanceTable of Contents Nomenclature IntroductionPRE-START Check List Operating InstructionsStarting & Operation Engine Electric Start Parking Brake Mower BladeStopping EngineEngine Must Begin to Stop if Cutting Height AdjustmentEngine Must not Start if Engine should Start ifSingle Blade Deck Service After First 5 HoursChange Engine OIL Check Mower BladeEngine Oil Oil Filter Air Filter Service Every 25 Operating HoursChecking Mower Belt Tension Engine Engine Cooling SystemMower Components Check EngineUnderside View of 33 Deck Front Caster Wheel Pivot Shaft Scrambler Lubrication 1. Front Wheel BearingsParking Brake Pivot Bushings Storage OUT of Season Service AnnuallyEngine Adjustments & Repair Joystick AdjustmentsNeutral Position Adjustments Forward Speed AdjustmentsBelt Removal Mower Drive Belt AdjustmentBelt Replacement DeckIdler ARM and Belt Guide Detail Blade Brake AdjustmentBelt Replacements From Previous+ 1/16 From Previous Page Checking the 33 Deck BladeDeck Shown Front or Rear View of DeckMower Deck Timing ROD Front to Rear Deck Pitch 38 DecksMower Blade Replacement 4.4.1. Blade Wear Limits Wheel Brake AdjustmentBlade Sharpening Battery Service Blade Replacement ChartMower Blade Replacement 4.4.3. Blade Replacement Battery Battery RemovalNEW Battery Preparation 1. Remove battery from carton Battery TestingTrouble Shooting on Next Problem Probable CauseCorrective Action Excessive Vibration Problem Probable Cause Corrective ActionUSE HRS Season Service Performed EachMAINTENANCE/REPLACEMENT Parts 100Disclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Page Page Scrambler Hydro Drive Series

YZ18386BVE, YZ18386BVE, YZ18336BVE, YZ18386BVE specifications

Snapper, a renowned name in the lawn care industry, offers a diverse range of powerful and efficient mowers suitable for both residential and commercial landscaping needs. Among their exceptional models are the Snapper YZ18336BVE, YZ18386BVE, and YZ18386BVE, each designed to deliver impressive performance and durability.

The Snapper YZ18336BVE is equipped with a robust 18-horsepower engine, providing ample power for tackling various lawn conditions. With a cutting width of 36 inches, this mower offers efficient grass cutting while navigating through tight spaces with ease. This model features a lightweight and durable steel deck, ensuring longevity and resistance to wear-and-tear. The YZ18336BVE also incorporates a comfortable, adjustable seat that enhances user experience during prolonged mowing sessions. Additionally, its heavy-duty wheels offer stability on uneven terrain, making it a reliable choice for homeowners and professionals alike.

Moving to the Snapper YZ18386BVE, this model takes the power up a notch with its 18-horsepower engine and increases the cutting width to an impressive 38 inches, allowing for enhanced productivity. The YZ18386BVE boasts Snapper's signature Easy Start technology, which guarantees quick and hassle-free engine startup every time. This model features advanced cutting technologies like the mulching capability and side discharge options, providing versatility in grass management. The robust design of the YZ18386BVE makes it ideal for tackling larger yards and commercial spaces while ensuring the highest standards of performance.

While the specifications and features of the YZ18386BVE are striking, it's important to note that the YZ18386BVE repeats its excellent performance attributes, showcasing Snapper's commitment to consistency and reliability across its product line. Users can expect the same powerful engine options and innovative design elements that make the YZ18386BVE a top-choice mower.

In conclusion, Snapper's offerings, including the YZ18336BVE and YZ18386BVE, exemplify the brand's dedication to quality and user satisfaction. With features such as powerful engines, durable steel construction, versatile cutting options, and user-friendly designs, Snapper mowers cater to various lawn care needs. Whether you are a homeowner looking to maintain your garden or a landscaping professional seeking robust equipment, Snapper's YZ18336BVE and YZ18386BVE models are perfect choices that promise performance and reliability.
Top Page Image Contents