Snapper ZF6101M, ZF2501KH, ZF5201M, ZF2501KH, ZF5201M, ZF6101M Operation, Maintenance

Page 3

IMPORTANT SAFETY INSTRUCTIONS

PREPARATION

(Continued From Previous Page)

4.Handle fuel with extra care. Fuels are flammable and vapors are explosive. Use only an approved fuel container. DO NOT remove fuel cap or add fuel with engine running. Add or drain fuel outdoors only with engine stopped and cool. Clean spilled fuel from machine. DO NOT smoke.

5.Practice operation of machine with BLADES OFF to learn controls and develop skills.

6.Check the area to be mowed and remove all objects such as toys, wire, rocks, limbs and other objects that could cause injury if thrown by blades or interfere with mowing.

7.Evaluate the terrain to determine what accessories and attachments are needed to properly and safely perform the job. Only use accessories and attachments approved by SNAPPER.

8.Keep people and pets out of mowing area. Immediately, STOP blades, STOP engine, and STOP machine if anyone enters the area.

9.DO NOT operate machine unless all shields, deflectors, switches, blade controls and other safety devices are in place and functioning properly.

10.Make sure all safety decals are clearly legible. Replace if damaged.

11.Protect yourself when mowing and wear appropriate clothing including safety glasses, long pants, ear protection, hardhat and substantial footwear with good traction. Long hair, loose clothing or jewelry may get tangled in moving parts.

12.Know how to STOP blades and engine quickly in preparation for emergencies.

13.Use extra care when loading or unloading the machine into a trailer or truck.

14.Check grass catcher components frequently for signs of wear or deterioration and replace as needed to prevent injury from thrown objects going through weak or worn spots.

OPERATION

1.Mount and dismount machine from left side.

2.Start engine from operator's seat. Make sure blades are OFF and parking brake is set. Use seat belts if provided.

3.DO NOT leave machine with engine running. Stop engine. Stop blades. Set brake. Remove key.

4.DO NOT operate machine unless properly seated with feet on foot rests or pedal(s).

5.DO NOT operate machine while under the influence of alcohol or drugs.

OPERATION

(Continued From Previous Column)

6.STOP MACHINE on level ground, lower deck, engage parking brake and make sure engine and blades have stopped before removing grass catcher or unclogging mower to prevent injury to hands or feet.

7.Blades must be OFF except when cutting grass. Set blades in highest position when mowing over rough ground.

8.Keep hands and feet away from rotating blades underneath deck. DO NOT place foot on ground while BLADES are ON or machine is in motion.

9.DO NOT operate machine without entire grass catcher or guards in place. DO NOT point discharge at people, passing cars, windows or doors.

10.Slow down before turning.

11.Watch out for traffic when near or crossing roadways.

12.STOP engine immediately after striking an object or if an abnormal vibration occurs. Remove key. Remove and disconnect the sparkplug wire. Make necessary repairs before resuming operation.

13.Mow only in daylight or with good artificial light.

14.Move motion control levers SLOWLY to maintain control during speed and directional changes.

15.Exercise CAUTION when pulling loads. DO NOT pull loads greater than 300 pounds. Avoid jack knifing. DO NOT turn sharply.

16.DO NOT operate engine in enclosed areas. Engine exhaust gases contain carbon monoxide, an odorless and deadly poison.

MAINTENANCE

1.DO NOT store machine or fuel container inside where fumes may reach an open flame, spark or pilot light such as in a water heater, furnace, clothes dryer or other gas appliance. Allow engine to cool before storing machine in an enclosure. Store fuel container out of the reach of children in a well ventilated, unoccupied building. Shut off fuel (when equipped with valve) while storing or transporting machine.

2.Clean grass and debris from engine, mufflers, drives and cutting units to help prevent overheating and fires. Clean up fuel, oil and excess grease.

3.When draining fuel tank, drain fuel into an approved container outdoors and away from open flame.

4.Check brakes frequently; adjust, repair or replace as needed.

5.Keep all bolts, nuts and screws properly tight. Check that all cotter pins are in proper position.

6.Always provide adequate ventilation when running engine. Engine exhaust gases contain carbon monoxide, an odorless and deadly poison.

3

Image 3
Contents Model Number Explanation Mower UnitManual No -3699 REV , 8/29/01 From Previous Column Protection for ChildrenProtection Against Tipovers PreparationOperation MaintenanceImportant Safety Instructions Table of Contents Nomenclature IntroductionSafety Messages and Symbols Safety Messages and Symbols Keep Children and Others OUT of Mowing Area PRE-START Check List Operating InstructionsStarting Engine Starting & Stopping ENGINE, Blades & Parking BrakeStopping Mower Blades Cutting Height AdjustmentStopping Engine Starting Mower BladesOperation Motion Control 3.3.1 Driving Machine Tighten to Mountingfoot Pounds Service After First 5 HoursChange Engine OIL Check Mower BladeAfter Every 25 Operating Hours Check Mower Drive BeltAnnually END of Each Season Riding Mower LubricationTransaxle Before Operating MachineDeck Removal Power Transfer Shaft RemovalNeutral Position Adjustments Adjustments & RepairMower Deck Adjustment Parking Brake AdjustmentEngine Adjustments & Repair Engine Belt Removal Mower Blade REPAIR/REPLACEMENT Blade Wear LimitsMower Drive Belt Replacement Blade SharpeningBattery Service Engine Belt ReplacementBattery Battery Removal Battery InstallationBattery Testing NEW Battery PreparationDo not Overfill Bearing Replacement Mower Spindles Field Serviceable SpindlesTrouble Shooting on Next Problem Probable Cause Corrective ActionTractor Will Not Move USE HRS Season Service Performed EachMAINTENANCE/REPLACEMENT Parts 100Disclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance OUT Front Z-RIDER Zero Turning Hydro Drive Series