Honeywell TE852ELW, TS815, TE852W Battery Installation, Mounting, Placement, Operation, Features

Page 4

B. BATTERY COMPARTMENT

•Holds two AA-size batteries

C.RESET

•Resets all previous settings

D.CHANNEL SWITCH

•Selects the desired channel -1,2 or 3

E.WALL-MOUNT RECESSED OPENING

•Keeps the remote sensor on the wall

F.°C/°F SWITCH

•Selects the temperature display in Fahrenheit or Celsius

NOTE: Install the batteries; select the channel and temperature in °C or °F before mounting the sensor.

BATTERY INSTALLATION

•Remove the screws from the battery compartment with a small Phillips screwdriver.

•Set the channel 1 through 3. The switch is located in the battery compartment. Channel 1 is typically selected if only one remote sensor is being used.

•Install 2 “AA” size alkaline batteries (not included) matching the polarities shown in the battery compartment.

•Select the temperature unit in °F or °C by pressing °C/°F switch with a paper clip or similar tool

•Replace the battery compartment door and secure the screws.

•Secure the remote sensor in the desired location.

MOUNTING

•The remote thermo-hygrometer sensor can be placed on the flat surface or mounted on the wall in vertical position

7

•Use the wall mount hardware and screws when mounting the thermo-hygrometer sensor on the wall

PLACEMENT

•The remote thermo-hygrometer sensor should be placed in the area with a free air circulation and sheltered from the direct sunlight and an extreme weather conditions.

•Ideally, place the thermo-hygrometer sensor above the natural surfaces (such as a grassy lawn).

•Avoid placing the thermo-hygrometer sensor near sources of heat, such as chimneys and heating elements.

•Avoid any areas collecting and radiating a heat from the sun, such as metal, brick or concrete structures, paving, patios and decks.

•The international standard for the valid air temperature measurements is 4 feet (1.25meters) above the ground.

OPERATION

Immediately after batteries are correctly installed, the remote sensor will start transmitting a temperature and humidity data to the main unit.

WIND SPEED METER

FEATURES

•Wind speed and wind gust measurement

•Measurement of the temperature at the place of the wind meter

•Remote transmission of the temperature, wind speed and gust data to the main unit via 433 MHz signal

•Operating range of up to 100 feet (30 meters)

•Wall or pole mount

78

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Installation Installation Standard Package ContentsIntroduction Remote Temperature & Humidity Sensor Before YOU BeginBattery Installation PlacementFeatures MountingAssembly Main UnitTime PowerWeather Front Rear D E F GTOP Side JK LM Weather and Time in EASY-TO Read DigitsNavigating Through the Modes SNOOZE/LIGHT buttonPressure Window DisplaysTemperature and Humidity Window Customazing Your Weather ForecasterWind Window SUNRISE/SUNSET WindowUsing Different Display Windows Pressure Window Setting Pressure ParametersBacklight Viewing Pressure and Altitude InformationViewing PRESSURE, Temperature and Himidity Charts Viewing Moon Phase History and Weather ForecastProgramming Pressure and Altitude Unit Viewing SEA Level Pressure HistoryUnderstanding Moon Phase Icons Accessing Clock WindowClock Window Programming Your LocationActivating or Deactivating Alarms Programming AlarmsManual Programming Different Clock and Calendar ModesActivating or Deactivating Snooze To disable time alarmsWwvb Radio Controlled Time Accessing SUNRISE/SUNSET Window SUNRISE/SUNSET WindowIcon Atomic Time Reception Strength Programming LATITUDE, LONGITUDE, Time Zone and DSTTemperature and Humidity Window Accessing Temperature and Humidity Window Viewing Remote Channel Temperature and HumidityRecalling Temperature and DEW Point Information Programming Temperature in Celsius or FahrengeitWind Window Precautions TroubleshootingMaintanance Appendix City Codes Use only fresh batteries. Do not mix new and old batteriesSpecifications FCC Statement Declaration of ConformityStandard Warranty Information
Top Page Image Contents