Honeywell TS13F Battery Installation, LOW Battery Warning, Placement of the Remote Sensor

Page 4

BATTERY INSTALLATION

NOTE: Install the batteries; select the channel and temperature in C° or F° before mounting the remote sensor.

•Remove the screws from the battery compartment with a small Phillips screwdriver.

•Set the channel (if channel switch is available in your model). The switch is located in the battery compartment. Channel 1 is typically selected if only one remote sensor is being used.

•Install 2 “AA” size alkaline batteries (not included) matching the polarities shown in the battery compartment.

•Replace the battery compartment door and secure the screws.

•Secure remote sensor in the desired location.

LOW BATTERY WARNING

A low-battery indicator [ ] will appear on the remote temperature reading line of the main unit, warning that the remote sensor batteries need replacement.

PLACEMENT OF THE REMOTE SENSOR

The remote sensor can be mounted on the wall using the recessed screw hole or placed on a flat surface indoors or outdoors.

GETTING STARTED

After batteries are installed; remote sensor will transmit temperature readings at 45 second intervals.

The main unit may take up to two minutes to receive the initial readings. Upon successful reception, remote temperature will appear on the main unit's display. The main unit will automatically update readings at 45-second intervals.

LOST COMMUNICATION

If the main unit display line for the remote sensor reading goes blank, refer to the main unit's User Manual to find out the way to begin a new signal search. If the signal still isn't received, please make sure that:

•The remote sensor is in its proper location.

•The distance between main unit and remote sensor is not over 100 feet (30meters).

•The path between units is clear of obstacles. Shorten the distance if necessary.

•Fresh batteries are installed correctly in both remote sensor

and main unit.

6

If there is no reception, please perform the following steps:

•Bring the main unit and remote sensor close together.

•Remove four (4) small screws from the back of the remote sensor with small Phillips screwdriver, and open the battery compartment.

•Remove the batteries from the battery compartment and reinstall them in the same manner. Remote sensor LED indicator will flash showing transmission of the signal.

•Remove the batteries from the main unit and reinstall them in the same manner.

•The remote temperature appeared on the main unit's display will show that transmission is being received successfully.

TRANSMISSION COLLISION

Signals from the other household devices such as wireless doorbells, home security systems, and entry control, may interfere with this product or cause temporary reception interruption. This is normal and will not affect the general performance of the product. The transmission and reception of the temperature readings will resume once the interference subsides.

PRECAUTIONS

This product is engineered to give you years of satisfactory service if handled carefully. Here are a few precautions:

•Do not immerse the unit in water.

•Do not clean the unit with abrasive or corrosive materials. They may scratch the plastic parts and corrode the electronic circuits.

•Do not subject the product to excessive force, shock, dust, temperature, or humidity, which may result in malfunctions, shorter lifespan, damaged batteries, and damaged parts.

•Do not tamper with the unit's internal components. Doing so will invalidate the warranty and may cause damage. This unit contains no user-serviceable parts.

•Use only fresh batteries. Do not mix new and old batteries.

•Read the user's manual thoroughly before operating the unit.

7

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Temperature Sensor With Probe Table of Contents IntroductionLED Indicator Battery CompartmentReset Channel SwitchBattery Installation LOW Battery WarningPlacement of the Remote Sensor PrecautionsFCC Statement SpecificationsDeclaration of Conformity Standard Warranty Information Sensor de temperatura Con sonda Tabla DE Contenidos IntroducciónFunción Reset Reseña GeneralIndicador LED Compartimento DE LA BateríaInstalación DE LA Batería Advertencia DE Batería BajaUbicación DEL Sensor Remoto InicioEspecificaciones Declaración DE ConformidadPage Capteur de température Avec sonde Table DES Matières PrésentationBouton Rétablir « Reset » Présentation DU ProduitIndicateur DEL Compartiment Pour PilesLinstallation DES Piles Lavertisseur DE Pile FaibleLE Démarrage LA Perte DE CommunicationsLES Spécifications LES Mesures DE SécuritéLA Déclaration DE LA FCC LA Déclaration DE Conformité LES Informations DE Garantie Standard

TS13F specifications

The Honeywell TS13F is a leading edge temperature and humidity sensor specifically designed for demanding commercial and industrial applications. Renowned for its reliability, accurate measurements, and user-friendly features, the TS13F is an excellent choice for a wide array of environments, from data centers to pharmaceutical facilities.

One of the key features of the Honeywell TS13F is its exceptional precision. The sensor is capable of measuring temperatures ranging from -40°C to 125°C with a high degree of accuracy. This robust range allows it to perform effectively in extreme conditions, making it ideal for both heating and cooling systems. In addition to temperature sensing, the TS13F also provides reliable humidity measurements, with a range of 0% to 100% relative humidity and excellent linearity.

The TS13F employs advanced capacitive technology to ensure extended reliability and performance. This technology minimizes drift over time, meaning that users can rely on the data gathered without necessitating frequent recalibrations. Moreover, the sensor’s design includes a hygroscopic material that enhances the speed of response, allowing it to capture rapid changes in humidity levels swiftly.

Another standout characteristic of the TS13F is its easy integration into existing systems. The device supports various output signals, including analog and digital formats, ensuring compatibility with a range of monitoring systems, Building Management Systems (BMS), and automation controls. This flexibility not only simplifies installation but also enhances system interoperability.

The TS13F is built with durability in mind. It features a robust housing that protects it from environmental challenges, including dust and moisture ingress. Furthermore, its operational stability across a wide range of temperatures equips it for use in both indoor and outdoor applications.

User-friendly features, such as quick setup and intuitive calibration processes, make the TS13F accessible to professionals with varying levels of expertise. Its compact design not only saves space but also allows for versatile mounting options, making it suitable for various applications.

In summary, the Honeywell TS13F temperature and humidity sensor stands out in the market for its accuracy, reliability, and ease of integration. Its combination of advanced technologies, robust design, and user-friendly features make it a prime choice for companies seeking an efficient and dependable environmental monitoring solution.
Top Page Image Contents