Eagle Electronics 320C manual Metal Nut washer Rubber, Washers, Bolt, Transom

Page 20

Metal

Nut washer

Rubber

Metal washer

washers

 

Bolt

Assemble transducer and bracket.

4.Drilling mounting holes. Hold the transducer and bracket assembly against the transom. The transducer should be roughly parallel to the ground. The transducer's centerline should be in line with the bottom of the hull. Don't let the bracket extend below the hull!

Mark the center of each slot for the mounting screw pilot holes. You will drill one hole in the center of each slot.

Drill the holes using the #29 bit (for the #10 screws).

Transom

Transom

Position transducer mount on transom and mark mounting holes.

Side view shown at left and seen from above at right.

18

Image 20
Contents Installation and Operation Instructions Eagle Electronics Box Catoosa, OK USA Table of Contents Advanced Sonar Options & Other Features Troubleshooting Page Capabilities and Specifications FishEasy 320C GeneralAudible alarms Current drainBack-up memory SonarHow Sonar Works How to use this manual typographical conventions Menu CommandsArrow Keys KeyboardPress ↓ to Fish ID Symbolsentexitexit Instructions = Menu SequencesPage Transducer Installation PreparationsTransom installation Trolling motor installationsShoot-through hull installations Recommended Tools and suppliesSelecting a Transducer Location Deadrise less than Strakes PadTransom Transducer centerline Hull bottom How low should you go?Good location Poor location Location Poor angle Shoot-thru-hull vs. Transom Mounting Transom Transducer Assembly And Mounting DotRatchets Metal Nut washer Rubber WashersBolt TransomBottom Hull Flat-bottom hull Deep-vee hull Trolling Motor Bracket Installation Transducer Orientation And Fish Arches Internal tooth washer TMB-S bracket Bolt Nut Flat washerTransducer angles and their effects on fish arches Hulls With Floatation Materials Testing Determines Best Location Transducer location High speed Trolling speedSecond bottom True bottom Manual range setting Epoxy transducer to hull Page Speed/Temperature Sensors HST-WSU HST-WSU Speed Sensor Installation Good location Transom Bottom of hullPower Connections Page Bracket Installation Mounting the Sonar Unit In-Dash, Bracket or Portable76.9 Millimeter 70.3 Inch Using the Quick Release Mounting Bracket107.5 82.7 156 Screw hole Power/transducer cable Cable slot Ratchet RearDepress ratchets to release Portable Sonar InstallationBracket front Installing the Batteries Page Cup Bolt Nut Washer Transducer Portable Transducer AssemblyTie nylon cord here Suction Cup Hull TransducerMENU/PWR menu and power Keyboard BasicsMemory MenusENT/PAGES enter and pages UP and Down ArrowsMain Menu Commands Main MenuSonar Menu Sonar Menu Commands Pages Page Sonar chart display options digital data Basic Sonar Quick Reference Sonar Operations Bait school Thermocline With fish Fish Arches To adjust sensitivity Fish Symbols vs. Full Sonar Chart To Restore Factory SettingsOther Free Training Aids Page Advanced Sonar Options & Other Features ASP Advanced Signal ProcessingTo change the ASP level AlarmsDepth Alarms To adjust and turn on the shallow alarm To adjust and turn on the deep alarmBacklight Level Fish AlarmTo turn the fish alarm on Calibrate Speed Chart Speed ColorLine Contrast Thin or no ColorLine Wider ColorLineDepth Cursor Cursor line Depth boxDepth Range Automatic Depth Range ManualTo turn Auto Depth Range on again To switch to Manual Depth RangeFasTrack Fish I.D. Fish Symbols & Depths To turn the Fish I.D. feature on FishTrackSymbols with FishTrack depths HyperScrollOverlay Data To turn on FishTrackTo turn off displayed data Tip To change displayed data font sizePing Speed & HyperScroll To change Ping Speed To turn off HyperScrollReset Options Pop-up HelpSensitivity & Auto Sensitivity Reset Water DistanceScreen Contrast and Backlight Level To adjust sensitivity in auto mode Automatic SensitivityTo adjust sensitivity in manual mode To turn Auto Sensitivity back onSet Keel Offset Set Language Software Version InformationFrom the Sonar Page, press MENU↓ to Sonar Featuresent Press MENUMENU↓ to Software InfoentFull Sonar Chart Split Zoom Sonar ChartDigital Data/Chart Stop Chart Sonar SimulatorTo adjust the Surface Clarity level Surface ClarityTransparency Press ↓ or ↑ to select clarity levelEXITEXITEXITTo adjust Menu Transparency level Units of MeasureZoom & Zoom Bar VolumeTo adjust volume To switch to zoom To turn on the Zoom BarZoom Pan Page Unit freezes, locks up, or operates erratically Unit operates only in demo modeUnit wont turn on Page No fish arches when the Fish I.D. feature is off NoisePage Index Page Eagle Electronics Full ONE-YEAR Warranty How to Obtain Service… Accessory Ordering Information for all countries Visit our web site

320C specifications

Eagle Electronics has made significant strides in the world of marine electronics with the introduction of the Eagle Electronics 320C. This compact, feature-packed device is designed to cater to both novice and experienced anglers, providing them with the necessary tools to enhance their fishing experience.

One of the standout features of the Eagle 320C is its high-resolution color display. With a screen size of 3.5 inches, the unit exhibits a bright and vibrant backlit display, ensuring exceptional visibility even in bright sunlight. The 320C employs a user-friendly interface, allowing quick navigation through its various functions and settings.

The 320C is equipped with advanced sonar technology, featuring dual-frequency capabilities. This enables users to switch between 83 kHz for wider coverage and 200 kHz for more precise detail. This flexibility in frequency options allows anglers to target specific fish species and efficiently optimize their fishing strategies. The device also boasts a powerful 300-watt RMS power output, ensuring clear and accurate sonar readings down to depths of 600 feet.

Another important characteristic of the Eagle 320C is its ability to display detailed bathymetric maps. With built-in mapping capabilities, users can access contour mapping, which provides essential information about the underwater landscape. This feature is especially valuable for locating structures such as submerged rocks or vegetation, which are often prime habitats for fish.

In addition to sonar and mapping functions, the Eagle 320C also includes a variety of customizable settings. Users can personalize various aspects of the display, including color palettes, sensitivity, and sonar depth range to suit their preferences. This level of customization helps maximize the device’s effectiveness in diverse fishing conditions.

Moreover, the Eagle Electronics 320C is designed with durability in mind. It features a rugged, waterproof casing that is built to withstand harsh marine environments. This resilience ensures that the device can reliably face saltwater exposure, rain, and other challenging conditions commonly encountered while fishing.

Overall, the Eagle Electronics 320C is an exceptional tool for anglers seeking a comprehensive fishing solution. With its high-resolution color display, advanced sonar capabilities, detailed mapping functionalities, and customizable settings, the 320C provides a robust platform for enhancing fishing success, making it a valuable addition to any boat.