Fantom Vacuum VPW46H Maintenance & Cleaning, Storing Your Pressure Washer, Motor Thermostat

GETTING TO KNOW YOUR PRESSURE WASHER

OPERATING INSTRUCTIONS

1.	Pressure Washer	15.	Trigger
2.	Water Intake	16.	Trigger Lock
3.	Water Intake Filter	17.	High Pressure Hose Connector
4.	On/Off Switch	18.	Brush
5.	Handle	19.	High Pressure Hose
6.	Detergent Tank	20.	13-ft Drain Snake (For outdoor use ONLY)
7.	High Pressure Output	21.	Hose Connector
8.	Power Cord	22.	Garden Hose Coupling
9.	Wheels (x2)	23.	Phillips Screw 1 1/4–inch long (x1)
10.	Wheel Locks (x2)		(not shown)
11.	Front Support	24.	Phillips Screw 7/8-inch long (x2)
12.	Adjustable Fan Jet Lance		(not shown)
13.	high pressure lance	25.	Phillips Screw 1-inch long (x1 nickel plate)
14.	Trigger Gun		(not shown)

Illustrations may differ from actual product.

Technical Specifications

Voltage:	120V., 60Hz.
Power:	13 Amps
Pressure:	1750 psi. (max)
Flow Rate:	1.65 GpH

3

Maintenance & Cleaning

Lubrication: The pressure washer is supplied with a closed lubrication system, so no addition of oil is needed.

Checking the Water Intake Filter: The water intake filter is located inside the water intake connector. (Fig. 18). Remove periodically and inspect for any deposits that might accumulate there.

Hose Connector

Water Intake

Fig. 18

Cleaning the Nozzles: If you notice that the output pressure fluctuates, you may have to clean the nozzles. Turn the unit "Off". Unplug from electric outlet and disconnect the water supply. Remove the lances, trigger gun and hose from unit. Take the small metal pin provided and insert into the nozzle end to remove any obstructions. (Fig. 19)

Fig. 19

This will occur more frequently if your water supply is very hard.

Storing Your Pressure Washer

When you have finished using your pressure washer, follow these steps for safe storage:

1.Turn the pressure washer to the "Off" position.

2.Turn off the water supply.

3.Before disconnecting the high pressure hose connection, point the trigger gun in a safe direction away from you and discharge the high pressure water. Disconnect the high pressure hose from the pressure washer and trigger gun.

4.Disconnect garden hose from pressure washer.

5.Remove excess water from the pump by tipping the unit on both sides to drain any remaining water from the water intake and outlet fittings.

6.Drain detergent tank and flush with clean water.

7.Wipe away any remaining water on all parts and fittings.

8.Engage the trigger gun safety lock.

9.Store the unit and accessories in a room above 32°F.

8

Winterizing & Long Term Storage

1.Disconnect all water connections.

2.Turn the pressure washer on for a few seconds, until any remaining water in the pump exits.

3.Turn the unit off immediately.

4.Store the pressure washer, parts and accessories in an area with a temperature above 32°F.

Motor Thermostat

Important: This pressure washer is equipped with a motor thermostat. The motor will stop if it is overheating. Wait 10-20 minutes before starting the unit again. If it stops again, please call FANTOM customer service at 1-800-798-7398.

Ground Fault Circuit Interrupter (GFCI)

This unit is equipped with a Ground Fault Circuit Interrupter (GFCI) built into the plug. This device provides additional protection from the risk of electrical shock. When connecting the GFCI to the electrical outlet, the indicator should appear red. If the indicator is not red, depress the RESET button on the GFCI until the indicator appears red.

Cleaning Tips

Wood Decks: Rinse deck and surrounding area with fresh water. If using detergent, fill the detergent applicator bottle and apply to the area being cleaned. For optimal results, reduce your work area to small sections and clean each section one at a time. Allow the detergent to rest on the surface for a few minutes and then rinse at high pressure. Do not let the detergent dry on the deck. Always clean from left to right and top to bottom for best results. Rinse at high pressure using the fan jet keeping the tip of the spray nozzle 8-12 inches from the surface. Caution: For soft woods, increase the distance from the cleaning surface.

Cars, Boats, & Motorcycles: Wet down area to be cleaned before applying detergent with clean water. Fill the detergent applicator bottle and apply to the area being cleaned. To achieve best results, clean one side at a time. Allow the detergent to rest on the surface for a few minutes but do not let it dry. Rinse at high pressure using the fan jet in a sweeping motion keeping the tip of the spray nozzle at least 8-10 inches away from the surface. Maintain a further distance when using a direct spray. Wipe surface for a polished finish.