Diamond Audio Technology HA 750.1, HA 700.4, HA 700.2 installation manual Metal has a grommet

Page 5
Sub-Sonic Adjustment - This control allows you to remove the unwanted sub-sonic frequencies below the tunning frequency of a ported enclosure. This helps to protect the woofer from over excursion.
ON / OFF Crossover Selection Switch - This switch allows you to turn on or off the crossover. In the OFF position, the crossover selection switch and adjustment knob have no effect. The HA 750.1 is only available as Low Pass.
Crossover Selection Switch - This switch allows you to select the crossover. Use High Pass for midrange or high frequency speakers. Use Low Pass for subwoofers. The HA 750.1 is only available as Low Pass.

1source unit using RCA type audio cables, keeping them away from power wiring wherever possible. On the 4 channel amplifier

(HA 700.4) “Front” and “Rear” input jacks are present. The“Pass-Thru” output allows the signal to pass on to other amplifiers. The Pass-Thru output is unaffected by the onboard crossover.RCA Input and Pass-Thru Output - These RCA jacks allow for a normal Left and Right channel signal input. Simply connect to the

2Input Gain Adjustment - This control matches the preamp stage of the HEX amplifier to your source unit. This is NOT a volume control. The range is between 150mV and 5V.

3

4

5Crossover Adjustment - Use this adjustment to select the crossover point. Remember that your choice will be directed to High Pass or Low Pass depending upon the position of the adjacent switch.

6

7and tweeters. 0 to 180 degrees of available adjustment capability. This is EXTREMLY useful to get the best and MOST bass out of your system.Phase Adjustment (HA 750.1) - This control allows you to adjust the "phase" so as to align the subwoofer in "time" to the mids

8

Bass Boost - This control adds 0 to +12dB (HA 750.1 only) of boost at 45Hz. Be cautious when adding boost to some

subwoofer

systems as they may not be able to handle the additional low frequency boost. In the OFF position, no bass boost is added.

 

9power supply and output stage of the slave amplifier(s) to the Master amplifier. This eliminates noise and the need to adjust the slave amplifier(s), while increasing efficiency.Master/Slave Port - This port is used in conjunction with the Master/Slave switch. This cable is nessesary to synchronize the

10

Master/Slave Switch - This switch is used when connecting multiple amplifiers. One amplifier should be assigned the MASTER and

the other(s) should be set to Slave. This will cause all of the amplifers set to Slave to function identical to the MASTER amplifier.

 

One remote level control knob pluged into the amplifier with the MASTER switch selected will now control both amplifiers.

11

Remote Level Adjustment (HA 750.1 Only) - This port is for the remote level control (included). The control is intended to allow

the user to control the level of gain up to the maximum adjustment level set on the amplifier. The control does not add additional

 

boost, it only attenuates the setting that is fixed at the amplifier’s control panel.

12

Status LED’s - These lights indicate when the amplifier is powered up normally and when there is a protection fault. See the

“Troubleshooting” section for details on what these useful indicators can tell you if there’s a problem.

13

Power Input Connections - These connections are for input power, chassis ground, and remote turn-on. Use a minimum of 4

gauge wiring for power and ground connections. The terminals will handle up to 4 gauge . Be sure any wiring that passes through

 

metal has a grommet!

14

Power Fuses - Standard automotive type ATC/ATO fuses are used on HEX Series Amplifiers. Always replace with the correct

fuse size. Never insert fuses of higher values. Doing so will void the warranty of your HEX amplifier. Also include a main fuse at

 

the connection to the vehicle battery within 18 inches (45.7 mm) of the positive battery post. It is also important to upgrade the

 

connection between the negative battery post and the chassis of the vehicle. This greatly reduces possibilities of weak electrical

 

“links” in the circuit.

15

Speaker Output Terminals - Connect your speakers to these terminals. Stereo connections are made as labeled. Bridged

connections use the LEFT + and RIGHT - as the two connections. The 2 and 4 channel amplifiers will perform into 2 Ohm stereo

loads or 4 Ohm bridged loads. DO NOT run 2 Ohm bridged loads on these amplifiers! The HA 750.1 is the only amplifier in the series capable of driving a load as low as 1 Ohm.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Amplifier Installation Manual Congratulations HA 700.2 / HA 700.4 / HA 750.1 FeaturesChannel Amplifier Connections and Controls Metal has a grommet Importance of Pre-Planning Tools and SuppliesVehicle Electrical System Requirements Wiring the AmplifierMounting Locations Power Connections Channel Mode, 1 speaker per channel Connecting Multiple SpeakersGet Ready to Listen Installing the Remote Level ControllerAdjustment of Built-In Crossover All Models TroubleshootingDiamond Audio Warranty

HA 750.1, HA 700.2, HA 700.4 specifications

Diamond Audio Technology has established itself as a key player in the high-performance audio industry, particularly known for its innovative amplifiers. The Diamond Audio HA series, encompassing the HA 700.4, HA 750.1, and HA 700.2 models, is designed for audiophiles who demand top-notch sound quality and reliability.

The HA 700.4 is a robust four-channel amplifier that delivers an impressive 100 watts RMS per channel at 4 ohms, while producing an astonishing 200 watts RMS per channel at 2 ohms. This amplifier employs advanced Class A/B circuitry, ensuring that audio reproduction is both powerful and crystal clear. It is equipped with high-level inputs, making it versatile enough to integrate with factory-installed audio systems. The HA 700.4 features a variable crossover, which allows users to tailor the output to suit specific audio preferences and achieve a balanced soundscape.

Next in the series, we have the HA 750.1, a mono amplifier capable of producing up to 750 watts RMS at 1 ohm. This model is designed for enthusiasts seeking strong bass performance. Its powerful output is complemented by a low-pass filter, enabling users to optimize their subwoofer performance. The HA 750.1 utilizes a high-performance MOSFET power supply, which ensures efficient power delivery and minimizes distortion, resulting in deep, rich bass tones.

Completing the lineup is the HA 700.2, a versatile two-channel amplifier that delivers 110 watts RMS per channel at 4 ohms and 220 watts RMS at 2 ohms. Ideal for driving component speakers or smaller subwoofers, the HA 700.2 features similar Class A/B technology as its counterparts. Its compact design is perfect for installation in tighter spaces while maintaining thermal efficiency through built-in heat sinks.

All three amplifiers are designed with durability in mind, featuring heavy-duty aluminum chassis that resist corrosion and provide excellent heat dissipation. The inclusion of adjustable gain control and built-in protection circuits further ensures reliability and longevity under various operating conditions.

In summary, the Diamond Audio Technology HA 700.4, HA 750.1, and HA 700.2 amplifiers boast state-of-the-art technologies, robust outputs, and user-friendly features that cater to serious music lovers. Whether enhancing high-frequency details or delivering deep bass, these amplifiers provide an unparalleled audio experience, making them a worthy addition to any sound system.
Top Page Image Contents