Campbell Hausfeld PW1586, PW1587 specifications Unclogging Tip, Conexión del Sistema

Assembly Instructions and Parts List PW1586 & PW1587

Instrucciones de Montaje y Lista de Piezas PW1586 & PW1587

Figure 10

I- Pressure Washer On O - Off

II - Steamer On

people, animals, electrical components or objects that can be damaged by hot temperatures.

4.When the water tank is empty the unit will stop making steam but the heating element will remain “On” as long as the unit is plugged in and the power switch is in the “II” position. When the water tank is empty move the power switch to the “Off” position “O” before refill- ing the water tank. A prolonged dry use of three minutes or more can damage the steam boiler pump.

ATTENTION: The steamer is equipped with a max pressure valve. This safety system releases pressure under the tank when the nozzle in the steamer handle is blocked. If a blockage occurs you will see water coming from behind the water tank.

Figure 11

Unclogging Tip

In case the outlet steam tip gets clogged, a wire cleaner is provided.

1.Turn “Off” the steam unit and allow at least five minutes for unit to cool.

2.Insert end of wire tip cleaner into small opening repeatedly to unclog. (See Figure 11)

3.Turn “On” unit and continue use.

4.If tip/nozzle remains clogged, turn off the steam cleaner and allow it cool for at least 5 minutes. Using a 3mm allen wrench remove the nozzle (item 20 in parts list) from the end of the spray gun. With the nozzle removed, turn on the steamer to allow it force hot water through the hose and spray gun for 20 - 30 seconds. Turn off the steam cleaner and while it is cooling down clean the nozzle. Once the spray gun is cool, replace the nozzle using the 3mm allen wrench, turn on the steamer, and continue use.

Conexión del Sistema

1.Inserte la lanza en la pistola y gírela en el sentido de las agujas del reloj hasta que llegue a su tope, como se muestra en la Figura 4.

Figura 4 - Conexión de la pistola y lanza

2.	Verifique que el interruptor de energía esté
	en la posición "OFF" ("APAGADO").
3.	Conecte la manguera de alta presión y el
	conjunto de pistola en la unidad.
4.	Conecte la manguera de jardín según se
	explica en Instrucciones de conexión de la
	manguera de jardín.
5.	Enchufe el cordón de corriente en un toma-
	corrientes de 120 V con conexión a tierra,
	que se encuentre en un circuito dedicado.
6.	Abra la llave del agua.
7.	Si está operando la unidad en un plano
	inclinado como una calzada o cerro, la
	parte delantera de la unidad deberá estar
	dirigida hacia la bajada, como se muestra
	en la figura 5.
8.	Presione el gatillo y manténgalo presiona-
	do por 1 minuto para liberar la presión y
	remover el aire atrapado en el sistema.
9.	Mueva el interruptor "ON/OFF" (“ENCENDI-

Figura 5

Tips:

Surface Preparation / Cleaning

•Allow steam to penetrate dirty surface for a few seconds before applying brush to work area.

•Have paper towels or a cleaning rag handy – once steam loosens dirt you can easily wipe it up. Brushes

•Use triangle brush for interior surfaces.

•Use triangle brush covered with cloth for more delicate surfaces, such as leather seats.

•Use nylon bristle brush for rugs, console, etc.

•Use the brass bristle brush on hard surfaces such as barbeque grills or to remove rust and paint from metal objects.

www.chpower.com

DO/APAGADO”) a la posición "ON"

("ENCENDIDO").

NOTA: CONSULTE EL INSTRUCCIONES DE OPERACIÓN.

Plano/calzada/cerro inclinado

Tierra llana

6 11 Sp