Briggs & Stratton 020239-1 owner manual Pressure Washer Rinsing, Cleaning Chemical Injection Hose

Page 12

SpeedClean™ 2200 PSI Pressure Washer

4.Slide adjustable nozzle forward to low pressure mode. Detergent cannot be applied with nozzle in high pressure position.

5.Make sure garden hose is connected to water inlet. Check that high pressure hose is connected to spray gun and pump. Start engine.

6.Apply detergent to a dry surface, starting at lower portion of area to be washed and work upward, using long, even, overlapping strokes.

7.Allow detergent to "soak in" for 3-5 minutes before washing and rinsing. Reapply as needed to prevent surface from drying. DO NOT allow detergent to dry on (prevents streaking).

IMPORTANT: You must flush the chemical injection system after each use by placing the filter into a bucket of clean water, then run the pressure washer in low pressure for 1-2 minutes.

Pressure Washer Rinsing

For Rinsing:

1.Slide the nozzle backward to high pressure, press the trigger and wait for the detergent to clear.

NOTE: You can also stop detergent from flowing by simply removing chemical injection hose from bottle.

2.Keep the spray gun a safe distance from the area you plan to spray.

WARNING

High pressure spray could cause you to fall if you are too close to the cleaning surface.

•Keep spray nozzle between 8 to 24 inches away from cleaning surface.

•Operate this unit on a stable surface.

•Be extremely careful if you must use the pressure washer from a ladder, scaffolding or any other relatively unstable location.

•Firmly grasp spray gun with both hands when using high pressure spray to avoid injury if gun kicks back.

3.Apply a high pressure spray to a small area, then check the surface for damage. If no damage is found, it is okay to continue cleaning.

4.Start at the top of the area to be rinsed, working down with same overlapping strokes as you used for washing and applying detergent.

Cleaning Chemical Injection Hose

If you used the chemical injection hose, you must flush it with clean water before stopping the engine.

1.Place chemical injection hose in a bucket full of clean water.

2.Slide adjustable nozzle forward to low pressure position. Flush for 1-2 minutes.

3.Shut off engine.

IMPORTANT: Simply shutting OFF engine will not release pressure in the system. When the engine has

shut down, squeeze the trigger on the spray gun to relieve the pressure in the hose.

Automatic Cool Down System

(Thermal Relief)

If you run the engine on your pressure washer for

3-5 minutes without pressing the trigger on the spray gun, circulating water in the pump can reach temperatures above 125°F.The system engages to cool the pump by

discharging the warm water onto the ground.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents 2200PSI Table of Contents Safety RulesEquipment Description When Adding Fuel Operate pressure washer only outdoorsHigh pressure spray may damage fragile items including glass Know Your Pressure Washer Choke Lever Prepares a cold engine for startingHigh Pressure Outlet Connection for high pressure hose High Pressure OutletAssembly Carton ContentsPreparing Pressure Washer for USE Remove Pressure Washer From CartonInstall Wheel Kit Refer to and install the wheel kit as followsAdd Engine Oil and Fuel Place pressure washer on a level surfaceChecklist Before Starting Engine Connect Hose and Water Supply to PumpConnect high pressure Hose here HOW to USE Your Pressure Washer How to Start Your Pressure WasherPressure Washer Location Pressure Washer ClearanceHow to Stop Your Pressure Washer How to Use the Adjustable NozzleEngage trigger lock on spray gun when not in use Let engine idle for two minutesHow to Use the Floor and Utility Brushes Applying Detergent with the Adjustable NozzleCleaning Chemical Injection Hose Pressure Washer RinsingAutomatic Cool Down System Thermal ReliefSpecifications General Maintenance RecommendationsPressure Washer Maintenance Nozzle Maintenance Ring MaintenancePump Maintenance Engine Maintenance Preparing the Unit for StorageStoring the Engine Protecting the PumpTroubleshooting Problem Cause CorrectionConsumer Use Years Years or YearConserve Estas Instrucciones Tabla DE Contenidos Descripción DEL EquipoReglas DE Seguridad AdvertenciaCuando Añada Combustible Precaución Conozca SU Maquina Lavadora DE Presion Filtro y Tubo para Recolección de Detergente noEntrada de Agua Toma de Alta Presión Tapa del Depósito del Aceite Llene el motor con aceiteMontaje Preparando EL Lavador a Presión Para SU USOAgregar Aceite al Motor y Gasolina Conecte la Manguera y el Suministro de Agua a la BombaLista de Revision Previa al Arranque del Motor Deposite la gasolina adecuada en el tanque del combustibleCómo Usar SU Máquina Lavadora a Presión Ubicación del Lavadora a PresiónCómo Darle Arranque a su Máquina Lavadora a Presión Espacio Libre Alrededor del Lavadora a PresiónCómo Detener su Máquina Lavadora a Presión Cómo Usar la Boquilla AjustableLavadora de Presión 2000 PSI de SpeedClean Cómo Utilizar los Cepillos de Suelo y de UtilidadAplicación del Detergente Usando la Boquilla Ajustable Enjuage de la Máquina Lavadora a Presión Limpiando el TuboSistema de Enfriamiento Automático Alivio Térmico Para EnjuageEspecificaciones Recomendaciones GeneralesMantenimiento DE LA Maquina Lavadora a Presion Mantenimiento de la Boquilla Mantenimiento de los Anillos OMantenimiento de la Bomba Mantenimiento DEL Motor Preparando LA Unidad Para SU AlmacenamientoAlmacenando EL Motor Proteger la BombaReparacion DE Averias Garantía Limitada
Top Page Image Contents