Poulan HDF550N HOW to USE Your Tiller, Stopping See Fig, Tine Operation See Fig, Tilling

Page 7

OPERATION

The operation of any tiller can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your tiller and while tilling. We recommend a wide vision safety mask for over spectacles or standard safety glasses.

HOW TO USE YOUR TILLER

Know how to operate all controls before adding fuel and oil or attempting to start engine.

STOPPING (See Fig. 5)

TINES

Release forward tine control to stop forward move- ment.

Release reverse tine control to stop reverse move- ment.

ENGINE

Move throttle control to “STOP” position.

Never use choke to stop engine.

 

 

 

 

FORWARD TINE CONTROL IN

 

 

 

REVERSE

“OFF” (UP) POSITION

 

 

 

 

 

 

 

CONTROL

 

 

 

 

 

FORWARD TINE CONTROL

 

 

 

 

IN “ON” (DOWN) POSITION

 

_

9

4

 

 

 

 

ndle

s

 

 

 

 

 

 

 

ha

 

 

 

 

 

 

 

 

THROTTLE

 

 

 

 

CONTROL

CHOKE

 

CONTROL

 

 

 

 

e

 

 

 

 

ngine_

 

 

 

 

art_

 

 

 

 

71

 

FIG. 5

TINE OPERATION (See Fig. 5)

FORWARD

Squeeze forward tine control to handle.

REVERSE

With forward tine control “OFF” (up) position, pull back and hold reverse tine control.

TILLING

The speed and depth of tilling is regulated by the position of the depth stake and wheel height.

The depth stake should always be below the wheels for digging. It serves as a brake to slow the tiller’s forward motion to enable the tines to penetrate the ground. Also, the more the depth stake is lowered into the ground the deeper the tines will dig.

DEPTH STAKE (See Fig. 6)

Adjust depth stake by removing the hairpin clip and clevis pin. Change depth stake to desired position. Replace the clevis pin and hairpin clip.

For normal tilling, set depth stake at the second or third hole from the top.

WHEELS (See Fig. 6)

Adjust wheels by removing the hairpin clip and clevis pin. Change wheel position. Replace the hairpin clip and clevis pin.

For normal tilling, set wheels at the second or third hole from the top.

depth_

HAIRPIN CLIP

AND CLEVIS PIN

stake

 

_

 

4

 

 

DEPTH

 

STAKE

 

STAKE

 

SPRING

 

WHEEL

FIG. 6

7

Image 7
Contents Model NO. HDF550N Preparation Safety RulesMaintenance and Storage TrainingTable of Contents Tools Required for Assembly AssemblyContents of Hardware Pack Tine Operation Unpack Carton & Install Handle See FigHandle Height Tilling WidthOperation Meets Ansi Safety RequirementsKnow Your Tiller Tilling HOW to USE Your TillerStopping See Fig Tine Operation See FigADD Gasoline Before Starting EngineTo Transport Fill Engine with OIL See FigTilling Hints Breaking in Your TillerCultivating Before Each USE MaintenanceLubrication Chart General RecommendationsEngine AIR Cleaner See FigSpark Plug CleaningCooling System See Fig MufflerTine Arrangement Service and AdjustmentsTo Adjust Handle Height See Fig TillerTo Remove Belt Guard See Fig Tine Operation Check See FigTo Replace V-BELTS See Figs To Adjust Carburetor Engine OIL StorageOther Fuel SystemTroubleshooting Points 187820X428 Handle AssemblyTiller - Model Number HDF550N KEY Part Description156705X011 Belt Guard and Pulley Assembly188502 736806009194R Pin, Clevis Wheel and Depth Stake AssemblyTineipb3 Tine Assembly187912 739006009173R Spacer, Split 189773 Decals157377 Decal, Logo 189787 176392Limited Warranty