Protection for Children, Preparation | Snapper IR5003B, NIR5003B

IMPORTANT SAFETY INSTRUCTIONS

WARNING: This powerful machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following instructions may result in serious injury to the operator or other persons. The owner of the tiller must understand these instructions and, furthermore, must allow only persons who understand these instructions to operate tiller. Each person operating the tiller must be of sound mind and body and must not be under the influence of any substance, which might impair vision, dexterity, or judgment. If you have any questions pertaining to your tiller which your dealer cannot answer to your satisfaction, call or write the Customer Service Department at SNAPPER, McDonough, Georgia, 30253. Phone: (1-800-935-2967).

PROTECTION FOR CHILDREN

1.DO NOT allow children in area when tiller is being operated.

2.DO NOT allow pre-teenage children to operate tiller.

3.Allow only responsible teenagers or adults with mature judgment to operate tiller and only under close supervision.

4.Keep the area clear of all persons, particularly small children, and pets.

5.Know how to STOP the tiller and disengage the controls quickly.

PREPARATION

1.Read this manual, get to know where all controls are located and practice how to use them before starting for the first time, and at the beginning of each season. Be thoroughly familiar with the controls and proper use of the equipment. Pay attention to Warning and Instructional Decals on engine and tiller.

2.Never operate tiller without proper guards, drag shield, plates, safety switches, or other safety protective devices in place and properly connected. Inspect to determine that these safety devices are installed properly, are in good repair, and operate properly. If the condition or operation of these devices are questionable, they must be repaired or replaced before using the tiller.

3.Thoroughly inspect the area where the tiller is to be used and remove all stones, sticks, wire, bones and other foreign objects. Also, note the location of holes, stumps, and other possible hazards.

4.DO NOT operate tiller when barefoot or wearing open sandals. Always wear long pants and substantial footwear with good traction.

5.Fill fuel tank outdoors and replace fuel cap before starting engine. Use approved fuel container. DO NOT smoke near open fuel container. DO NOT fill fuel tank indoors or when engine is running. Allow engine to cool for at least ten minutes before refilling. Wipe off any spilled fuel before starting engine. DO NOT run engine indoors.

6.Make sure that clutch is disengaged and transmission is in neutral (if so equipped) before starting engine.

OPERATIONAL PRECAUTIONS

1.DO NOT change engine governor settings or over speed engine.

2.DO NOT put hands or feet near or under rotating parts.

3.Exercise CAUTION when crossing gravel drives, walks, or roads, and under any conditions when tiller is transported. Look behind and use care when backing.

4.After striking a foreign object or if tiller vibrates abnormally, STOP the engine, disconnect and secure spark plug wire away from plug. Inspect the tiller for any damage and repair the damage.

5.When leaving tiller unattended, disengage clutch, shift transmission to neutral (if so equipped) and stop the engine.

6.Before removing debris or cleaning tines, repairing or inspecting make certain engine, tines and all moving parts have STOPPED. Disconnect and secure spark plug wire away from plug to prevent accidental starting.

7.Exercise CAUTION when changing directions while operating tiller. DO NOT till in areas where stability or traction is in doubt.

8.DO NOT overload the machine capacity by attempting to till too deep at too fast a rate.

9.Be extra careful when tilling hard ground. Use less tine engagement to maintain control of tiller.

10.Till only in daylight or in good artificial light.

11.Never operate tiller in wet areas. Always be sure of your footing; keep a firm hold on the handle.

12.Do not operate on slopes

MAINTENANCE AND STORAGE

1.Keep all nuts, bolts, and screws tight and be sure tiller is in safe operating condition.

2.Never store tiller with fuel in tank inside of a building where fumes may reach an open flame or spark. Allow engine to cool before storing in any enclosure.

3.To reduce fire hazard, keep engine free of spilled fuel, debris and excessive grease.

4.Have your tiller inspected and serviced each year by an authorized Snapper dealer. Determine if any additional devices are available which might upgrade the safety of your tiller.

5.Factory specified Snapper replacement parts must be used to assure adequate protection against injury.

IR5003B, NIR5003B specifications

The Snapper IR5003B and NIR5003B are advanced infrared thermometers that represent the pinnacle of modern temperature measurement technology. These devices have been engineered for precision, durability, and user-friendliness, making them ideal for both professional and amateur applications.

One of the key features of the IR5003B is its laser-guided targeting system. This allows users to accurately measure the temperature of specific surfaces or objects from a distance, ensuring that measurements are taken from exactly the right spot. The dual laser pointers aid in visualizing the measurement area, enhancing accuracy while reducing the chances of error that can occur with wider measurement fields.

The NIR5003B model further extends its capabilities by incorporating advanced non-contact temperature measurement technology. This feature is particularly valuable in applications where direct contact with the subject is not possible or practical, such as moving objects or hazardous materials. Users can obtain quick and accurate temperature readings without the risk of contamination or damage to sensitive surfaces.

Both models boast a wide temperature range, typically spanning from -50°C to 500°C, catering to a variety of use cases, from monitoring food safety to industrial applications. The high-resolution display provides easy visibility of readings, which can be crucial in fast-paced environments where quick decisions are necessary.

Another standout characteristic of the Snapper IR5003B and NIR5003B is their response time. These thermometers are designed to gather data swiftly, allowing users to track temperature changes in real time. This is particularly useful in processes that require consistent monitoring, such as HVAC systems, engine maintenance, and food preparation.

Additionally, these devices offer features like adjustable emissivity settings, enabling users to tailor the device to the properties of different materials for improved accuracy. The ergonomic design ensures that the devices are comfortable to hold and operate, reducing user fatigue during prolonged use.

In summary, the Snapper IR5003B and NIR5003B are versatile infrared thermometers that combine advanced technology and user-friendly features. With laser targeting, non-contact measurement capabilities, a broad temperature range, swift response times, and adjustable emissivity settings, they are designed to meet the demands of various industries efficiently and effectively. Whether for professional use or home applications, these thermometers are invaluable tools for anyone needing precise temperature measurements.