Poulan 188904 owner manual To Transport, Before Starting Engine, ADD Gasoline

Page 9

OPERATION

Swing the handle in the opposite direction you wish to turn, being careful to keep feet and legs away from tines.

When you have completed your turn-around, release the drive control bar and lower handle. Place shift lever in till position and move throttle control to desired speed. To begin tilling, hold drive control bar against the handle.

OUTER SIDE SHIELDS (See Fig. 11)

The back edges of the outer side shields are slotted so that the shields can be raised for deep tilling and lowered for shallow tilling to protect small plants from being buried. Loosen nut “A” in slot and nut “B”. Move shield to desired position (both sides). Retighten nuts.

TO TRANSPORT

CAUTION: Before lifting or transporting, allow tiller engine and muffler to cool. Disconnect spark plug wire. Drain gasoline from fuel tank.

AROUND THE YARD

Release the depth stake pin. Move the depth stake down to the top hole for transporting the tiller. Place depth stake pin in hole of depth stake to lock in posi- tion. This prevents tines from scuffing the ground.

Place shift lever indicator in “F” (forward) position for transporting.

Hold the drive control bar against the handle to start tiller movement. Tines will not turn.

Move throttle control to desired speed.

AROUND TOWN

Disconnect spark plug wire.

Drain fuel tank.

Transport in upright position to prevent oil leakage.

BEFORE STARTING ENGINE

IMPORTANT: BE VERY CAREFUL NOT TO ALLOW DIRT TO ENTER THE ENGINE WHEN CHECKING OR ADDING OIL OR FUEL. USE CLEAN OIL AND FUEL AND STORE IN APPROVED, CLEAN, COVERED CONTAINERS. USE CLEAN FILL FUNNELS.

CHECK ENGINE OIL LEVEL (See Fig. 12)

The engine in your unit has been shipped, from the factory, already filled with SAE 30 summer weight oil.

With engine level, clean area around oil filler plug and remove plug.

Engine oil should be to point of overflowing when engine is level. For approximate capacity see “PRODUCT SPECIFICATIONS” on page 3 of this manual. All oil must meet A.P.I. Service Classification SF-SJ.

Reinstall engine oil cap and tighten.

For cold weather operation you should change oil for easier starting (See oil viscosity chart in the Mainte- nance section of this manual).

To change engine oil, see the Maintenance section in this manual.

OIL

LEVEL

FIG. 12

ADD GASOLINE

Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

CAUTION: Fill to within 1/2 inch of top of fuel tank to prevent spills and to allow for fuel expansion. If gasoline is ac- cidentally spilled, move machine away from area of spill. Avoid creating any source of ignition until gasoline vapors have disappeared.

Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can at- tract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 13)

CAUTION: Keep drive control bar in “DISENGAGED” position when start- ing engine.

When starting engine for the first time or if engine has run out of fuel, it will take extra pulls of the recoil starter to move fuel from the tank to the engine.

9

Image 9
Contents PRRT65D Maintenance and Storage Safety RulesTraining PreparationTable of Contents Assembly Tools Required for AssemblyOPERATOR’S Position See Fig Unpacking Carton See Fig Install Handle See Figs , 4,Connect Shift ROD See Fig Attach Clutch Cable See FigRemove Tiller from Crate Check Tire PressureMeets Ansi Safety Requirements OperationKnow Your Tiller HOW to USE Your Tiller To Transport Before Starting EngineADD Gasoline Tine Shear Pins Tilling HintsCultivating Maintenance Schedule MaintenanceLubrication Chart General RecommendationsAIR Filter See Fig EngineCooling System See Fig CleaningMuffler Spark PlugService and Adjustments TillerTire Care To Replace Ground Drive Belt See Figs Ground Drive Belt Adjustment See FigTine Replacement See Figs , 25, To Adjust Carburetor To Adjust Throttle Control Cable See FigOther StorageFuel System Engine OILTroubleshooting Points Tiller - Model Number PRRT65D Handle Assembly165501X013 MAINFRAME, Left Side185190 Bumper MAINFRAME, Right SideKEY Part NO. NO. Description Tine Shield Tine Assembly Decals Limited Warranty Parts and Service

188904 specifications

The Poulan 188904 is a versatile and powerful chainsaw designed for both professional and residential use, making it an excellent choice for tree trimming, firewood cutting, and other landscaping tasks. Its robust performance and user-friendly features place it among the top options available in the market.

At the heart of the Poulan 188904 is a reliable two-stroke engine that delivers impressive power and efficiency. This engine is designed to provide the necessary torque and speed for effective cutting through a variety of woods, ensuring operational efficiency and minimizing downtime. With a displacement of approximately 38cc, this engine generates sufficient power to tackle medium-sized jobs with relative ease, making it ideal for homeowners and professionals alike.

One of the standout features of the Poulan 188904 is its lightweight and ergonomic design. Weighing in at around 10 lbs, it is easy to handle and maneuver, which is especially important during extended periods of use. The chainsaw is equipped with an adjustable rear handle that allows users to find a comfortable grip, reducing fatigue during operation.

The Poulan 188904 also incorporates several innovative technologies to enhance user experience and safety. It features an automatic chain oiler that ensures the chain is adequately lubricated during operation, prolonging the life of both the chain and the bar. Additionally, the chainsaw is designed with a tool-less chain tensioning system, making it quick and easy to adjust the chain's tension without the need for additional tools.

Safety is a key consideration in the design of the Poulan 188904. The chainsaw comes with safety features such as a low kickback chain and a chain brake that activates in the event of a kickback, protecting the user from potential injury. The handguard and anti-vibration handle provide added safety and comfort, ensuring a secure grip while minimizing vibrations during use.

Overall, the Poulan 188904 combines power, efficiency, and safety features, creating a reliable tool for various cutting tasks. Its lightweight design, innovative technologies, and emphasis on user comfort make it a popular choice among chainsaw users, from weekend gardeners to professional landscapers. Whether you're pruning branches or cutting firewood, the Poulan 188904 is a dependable partner that delivers consistent performance.