OPERATION
The operation of any tiller can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your tiller and while tilling. We recommend a wide vision safety mask for over spectacles or standard safety glasses.
00155
HOW TO USE YOUR TILLER
Know how to operate all controls before adding fuel and oil or attempting to start engine.
STOPPING (See Fig. 9)
TINES AND DRIVE
•Release drive control bar to stop movement.
•Move shift lever to “N” (neutral) position.
ENGINE
•Move throttle control to “STOP” position.
•Never use choke to stop engine.
THROTTLE
CONTROLSHIFT
LEVER
DRIVE CONTROL BAR “ENGAGED”
POSITION
DRIVE CONTROL BAR “DISENGAGED” POSITION
FIG. 9
TINE OPERATION - WITH WHEEL DRIVE
•Always release drive control bar before moving shift lever into another position.
•Tine movement is achieved by moving shift lever to
(
) till position and engaging drive control bar.
FORWARD - WHEELS ONLY/TINES STOPPED
•Release drive control bar and move shift lever indicator to “F” (forward) position. Engage drive control bar and tiller will move forward.
REVERSE - WHEELS ONLY/TINES STOPPED
•DO NOT STAND DIRECTLY BEHIND TILLER.
•Release the drive control bar.
•Move throttle control to “SLOW” position.
•Move shift lever indicator to “R” (reverse) position.
•Hold drive control bar against the handle to start tiller movement.
HARD TO SHIFT GEARS
•Briefly engage drive control bar and release or rock tiller forward and backward until are able to shift gears.
DEPTH STAKE (See Fig. 10)
The depth stake can be raised or lowered to allow you more versatile tilling and cultivating, or to more easily transport your tiller.
TRANSPORT
SHALLOWESTPOSITION TILLING
(CULTIVATING)
DEEPEST
TILLING
DEPTH
STAKE
|
|
|
|
|
| 2 |
|
|
|
|
| _ | |
|
|
|
| e |
| |
|
|
| k |
|
| |
|
| ta |
|
|
| |
| s |
|
|
|
| |
h_ |
|
|
|
|
| |
pt |
|
|
|
|
|
|
FIG. 10
TILLING (See Fig. 11)
•Release depth stake pin. Pull the depth stake up for increased tilling depth. Place depth stake pin in hole of depth stake to lock in position.
•Place shift lever indicator in tilling position.
•Hold the drive control bar against the handle to start tilling movement. Tines and wheels will both turn.
•Move throttle control to “FAST” position for deep tilling. To cultivate, throttle control can be set at any desired speed, depending on how fast or slow you wish to cultivate.
IMPORTANT: ALWAYS RELEASE DRIVE CONTROL BAR BEFORE MOVING SHIFT LEVER INTO ANOTHER POSITION.
|
| DEPTH STAKE PIN | |||
|
| “RELEASED” POSITION | |||
|
|
|
|
| “LOCKED” |
|
|
|
|
| POSITION |
NUT “B” |
|
|
|
|
|
|
|
|
|
| 1 |
|
|
|
| _ | |
OUTER | NUT “A” |
| e |
| |
k |
|
| |||
ta |
|
|
| ||
s |
|
|
| ||
SIDE SHIELD |
| _ |
|
|
|
| h |
|
|
| |
| ept |
|
|
| |
|
| d |
|
|
|
FIG. 11
TURNING
•Release the drive control bar.
•Move throttle control to “SLOW” position.
•Place shift lever indicator in “F” (forward) position. Tines will not turn.
•Lift handle to raise tines out of ground.
8