Poulan 401434 manual To Transport, Before Starting Engine, ADD Gasoline

Page 9

OPERATION

•Swing the handle in the opposite direction you wish to turn, being careful to keep feet and legs away from tines.

•When you have completed your turn-around, release the drive control bar and lower handle. Place shift lever in till position and move throttle control to desired speed. To begin tilling, hold drive control bar against the handle.

OUTER SIDE SHIELDS (See Fig. 11)

The back edges of the outer side shields are slotted so that the shields can be raised for deep tilling and lowered for shallow tilling to protect small plants from being buried. Loosen nut “A” in slot and nut “B”. Move shield to desired position (both sides). Retighten nuts.

TO TRANSPORT

CAUTION: Before lifting or transporting, allow tiller engine and muffler to cool. Disconnect spark plug wire. Drain gasoline from fuel tank.

AROUND THE YARD

•Release the depth stake pin. Move the depth stake down to the top hole for transporting the tiller. Place depth stake pin in hole of depth stake to lock in posi- tion. This prevents tines from scuffing the ground.

•Place shift lever indicator in “F” (forward) position for transporting.

•Hold the drive control bar against the handle to start tiller movement. Tines will not turn.

•Move throttle control to desired speed.

AROUND TOWN

•Disconnect spark plug wire.

•Drain fuel tank.

•Transport in upright position to prevent oil leakage.

BEFORE STARTING ENGINE

IMPORTANT: BE VERY CAREFUL NOT TO ALLOW DIRT TO ENTER THE ENGINE WHEN CHECKING OR ADDING OIL OR FUEL. USE CLEAN OIL AND FUEL AND STORE IN APPROVED, CLEAN, COVERED CONTAINERS. USE CLEAN FILL FUNNELS.

CHECK ENGINE OIL LEVEL (See Fig. 12)

•The engine in your unit has been shipped, from the factory, already filled with SAE 30 summer weight oil.

•With engine level, clean area around oil filler plug and remove plug.

•Engine oil should be to point of overflowing when engine is level. For approximate capacity see “PRODUCT SPECIFICATIONS” on page 3 of this manual. All oil must meet A.P.I. Service Classification SF-SJ.

•Reinstall engine oil cap and tighten.

•For cold weather operation you should change oil for easier starting (See oil viscosity chart in the Mainte- nance section of this manual).

•To change engine oil, see the Maintenance section in this manual.

OIL

LEVEL

FIG. 12

ADD GASOLINE

•Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

CAUTION: Fill to within 1/2 inch of top of fuel tank to prevent spills and to allow for fuel expansion. If gasoline is ac- cidentally spilled, move machine away from area of spill. Avoid creating any source of ignition until gasoline vapors have disappeared.

Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can at- tract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 13)

CAUTION: Keep drive control bar in “DISENGAGED” position when start- ing engine.

When starting engine for the first time or if engine has run out of fuel, it will take extra pulls of the recoil starter to move fuel from the tank to the engine.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Always Wear EYE Protection During Operation ModelMaintenance and Storage Safety RulesTraining PreparationTable of Contents Assembly Tools Required for AssemblyOPERATOR’S Position See Fig Unpacking Carton See Fig Install Handle See Figs , 4,Connect Shift ROD See Fig Attach Clutch Cable See FigRemove Tiller from Crate Check Tire PressureMeets Ansi Safety Requirements OperationKnow Your Tiller HOW to USE Your Tiller To Transport Before Starting EngineADD Gasoline Tine Shear Pins Tilling HintsCultivating Maintenance Schedule MaintenanceLubrication Chart General RecommendationsAIR Filter See Fig EngineCooling System See Fig CleaningMuffler Spark PlugService and Adjustments TillerTire Care To Replace Ground Drive Belt See Figs Ground Drive Belt Adjustment See FigTine Replacement See Figs , 25, To Adjust Carburetor To Adjust Throttle Control Cable See FigOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsService Notes Limited Warranty Parts and Service

401434 specifications

The Poulan 401434 is a well-renowned chainsaw that combines power, efficiency, and user-friendly features, making it a popular choice among both professional landscapers and DIY enthusiasts. Designed for optimal performance, the 401434 has gained a reputation for reliability and durability in various cutting tasks.

One of the standout features of the Poulan 401434 is its robust engine. It is powered by a potent 40cc two-stroke engine that delivers impressive performance for a wide range of cutting applications. This engine is designed to provide sufficient torque, enabling users to tackle even the toughest jobs with ease. The power output, combined with a well-balanced design, ensures that users can operate the saw comfortably for extended periods.

In addition to its strong performance, the Poulan 401434 incorporates advanced technology to enhance user experience. One such technology is the Easy Start system, which minimizes the effort required to start the chainsaw. This feature is especially beneficial for those who may have difficulty starting traditional two-stroke engines, as it allows for a smoother and more manageable startup process.

Safety is a top priority for Poulan, and the 401434 reflects this commitment. It comes with an integrated chain brake that automatically stops the chain's movement in case of kickback. This proactive safety feature provides peace of mind while operating the saw, making it a suitable choice for both novice and experienced users.

The Poulan 401434 also boasts a durable construction, featuring materials that are built to withstand the rigors of heavy use. The chainsaw's bar and chain are designed for long-lasting performance, requiring minimal maintenance. Additionally, the tool-less chain tensioning system allows for quick adjustments, making it easier for users to maintain optimal cutting conditions without needing additional tools.

Another noteworthy characteristic is the lightweight design of the Poulan 401434. Weighing in at just around 10 pounds, this chainsaw is easy to maneuver, reducing user fatigue and making it suitable for prolonged use. The ergonomic handle ensures a comfortable grip, allowing for precise control during cutting tasks.

In summary, the Poulan 401434 is an excellent chainsaw that features a powerful engine, user-friendly technology, and a focus on safety and durability. Its combination of performance and comfort makes it an ideal choice for anyone looking to tackle outdoor cutting tasks effectively and efficiently. Whether you're trimming branches, cutting firewood, or undertaking landscaping projects, the Poulan 401434 is designed to meet your needs.
Top Page Image Contents