Poulan 194800 manual Storage, Other, Fuel System, Engine OIL, Cylinders

Page 18

STORAGE

Immediately prepare your tiller for storage at the end of the season or if the unit will not be used for 30 days or more.

CAUTION: Never store the tiller with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TILLER

Clean entire tiller (See “CLEANING”in the Maintenance section of this manual).

Inspect and replace belts, if necessary (See belt re- placement instructions in the Service and Adjustments section of this manual).

Lubricate as shown in the Maintenance section of this manual.

Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

FUEL SYSTEM

IMPORTANT:IT IS IMPORTANTTO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS THE CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTUREWHICH LEADSTO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.

Empty the fuel tank by starting the engine and let it run until the fuel lines and carburetor are empty.

Never use engine or carburetor cleaner products in the fuel tank or permanent.

Use fresh fuel next season.

NOTE: Fuel stablizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stablizer container. Run engine at least 10 minutes after adding stablizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER(S)

Remove spark plug.

Pour 1 ounce (29 ml) of oil through spark plug hole into cylinder.

Pull starter handle slowly several times to distribute oil.

Replace with new spark plug.

OTHER

Do not store gasoline from one season to another.

Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

If possible, store your unit indoors and cover it to give protection from dust and dirt.

Cover your unit with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your unit to rust.

IMPORTANT: NEVER COVER TILLER WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.

18

Image 18
Contents Model Always Wear EYE Protection During OperationTraining Safety RulesMaintenance and Storage PreparationTable of Contents Assembly Tools Required for AssemblyOPERATOR’S Position See Fig Install Handle See Figs , 4, Unpacking Carton See FigRemove Tiller from Crate Attach Clutch Cable See FigConnect Shift ROD See Fig Check Tire PressureMeets Ansi Safety Requirements OperationKnow Your Tiller HOW to USE Your Tiller To Transport Before Starting EngineADD Gasoline Tine Shear Pins Tilling HintsCultivating Lubrication Chart MaintenanceMaintenance Schedule General RecommendationsEngine AIR Filter See FigMuffler CleaningCooling System See Fig Spark PlugService and Adjustments TillerTire Care Ground Drive Belt Adjustment See Fig To Replace Ground Drive Belt See FigsTine Replacement See Figs , 25, To Adjust Throttle Control Cable See Fig To Adjust CarburetorFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionService Notes Limited Warranty Parts and Service