Troy-Bilt 630B-Tuffy, 634F-Bronco, 634B-Super Bronco manual Decals, To Avoid Serious Injury

Page 5

	Section 1: Safety	5

Decals

For your safety and the safety of others, various safety and opera- tional decals are located on your unit (see Figure 1-2).

Keep the decals clean and legible at all times. Contact your local ser- vice dealer or the factory for replacements if any decals are damaged or missing.

Refer to the Parts List pages in this Manual for decal locations, descrip- tions and part numbers.

Forward Clutch Bail	Reverse Clutch Control
Forward Clutch Bail	Operating Instruction
Operating Instruction	(Models 634F/634B)

Starting Stabilization

Message (on engine)

Warning Messages

Hot Surfaces Warning

(on belt cover)

Figure 1-2: Location of safety and operating decals (5.5HP Model shown).

Operating Symbols

Various symbols (shown here, with word descriptions) may be used on the tiller and engine. Your unit may not have all of the symbols.

STOP

FAST SLOW STOP

R

CHOKE	CHOKE	REVERSE
		ROTATING
ON	OFF
		TINES
			BAIL
		BAIL
		ENGAGED	DISENGAGED
TILLER DIRECTION		LEVER DIRECTION

WARNING

TO AVOID SERIOUS INJURY:

•READ THE OWNER’S MANUAL.

•KNOW LOCATIONS AND FUNCTIONS OF ALL CONTROLS.

•KEEP ALL SAFETY DEVICES AND SHIELDS IN PLACE AND WORKING.

•NEVER ALLOW CHILDREN OR UNINSTRUCTED ADULTS TO OPERATE TILLER.

•SHUT OFF ENGINE AND DISCONNECT SPARK PLUG WIRE BEFORE MANUALLY UNCLOG- GING TINES OR MAKING REPAIRS.

•KEEP BYSTANDERS AWAY FROM MACHINE.

•KEEP AWAY FROM ROTATING PARTS.

•USE EXTREME CAUTION WHEN REVERSING OR PULLING THE MACHINE TOWARDS YOU.

Image 5

Contents Operator’s Manual Table of Contents Know how to stop the unit and disengage the controls quickly Safety Alert SymbolExercise caution to avoid slipping or falling SafetyKeep children and pets away Use slower engine speedsTo Avoid Serious Injury DecalsInspect Unit Assembly StepsIntroduction Clutch Cable Install Reverse Clutch Cable Models 634F and 634B only AssemblyCheck all nuts and screws for tightness Check AIR PressureCheck Level of Transmission Gear OIL Introduction Wheel Drive PinsEngine Controls Reverse Clutch Control Models 634F/634BHandlebar Height Adjustment Features and ControlsForward Clutch Bail Depth Regulator LeverIntroduction BREAK-IN Operation Pre-Start ChecklistStarting and Stopping the Engine Starting the EngineOperation Operating the TillerTines will cause injury Stopping the Engine and Tiller Stopping the Tiller and EngineBy successive passes at one Quarter width see Fig Clumps of soil that can interfere withYour freshly tilled or cultivated soil Terrace Gardening Read the following recommendations before tilling on slopesTilling Up and Down Slopes Vertical Tilling Loading and Unloading the Tiller Clearing the TinesTransmission Gear OIL Service Maintenance ScheduleTiller Lubrication Check for OIL LeaksRemoving/Installing a Single Tine MaintenanceRemoving/Installing a Tine Assembly Bolo TinesTo Check Forward Belt Tension Checking and AdjustingReplacement Belt Information Engine Cleaning AIR Cleaner Service Engine OIL Service Forward Clutch Bail AdjustmentChecking and Adjusting Reverse Drive Belt Tension To Check Reverse Belt TensionSpark Arrester Screen Service Spark Plug ServiceCARBURETOR/GOVERNOR Control Adjustments OFF Season StorageProblem Possible Cause Correction TroubleshootingOEM-290-256 fits Tuffy, OEM-290-254 fit Bronco OEM-290-265 fits Tuffy, Bronco & Super BroncoPart Description Parts ListDrawing no Parts List Part Description QTY Parts List Drawing noDRAWING/PARTS List no For Model 630B GW-9727 24 3 1917326 Hold Tine With Blunt End Toward You Left Side Right Side50049-02 TROY-BILT Tiller Lifetime Limited Warranty