Bolens 12228 Operation, PRE-START Preparation, Stopping Starting the Engine, OFF position

Page 7

Section

4

7

Operation

WARNING

Before operating the unit, carefully read and understand all safety, control and operating instructions in this Manual, the separate Engine Owner’s Manual and the decals on the machine.

10.Reconnect the spark plug wire.

11.Add gasoline to the fuel tank.

DANGER

GASOLINE IS HIGHLY FLAMMABLE AND ITS VAPORS ARE EXPLOSIVE.

B

A

Failure to follow these instructions can result in serious personal injury.

PRE-START PREPARATION

Before starting the engine, perform the fol- lowing checks and services:

1.

Disconnect the spark plug wire.

2.

Move the engine On/Off switch to the

OFF position.

Follow the gasoline safety rules in this Manual (Section 1) and in the separate Engine Owner’s Manual.

Failure to follow gasoline safety instruc- tions can result in serious personal injury and property damage.

IMPORTANT: Read the separate Engine Owner’s Manual before starting the engine. Never use stale or contaminated

Figure 4

C

Figure 5

Close

Open

3.

Check that all wires and cables are

properly and securely connected.

4.

Check that the six plastic cable ties (J,

Figure 2) are positioned as shown, and

that the cables are not kinked or jammed.

5.

Adjust handlebar height to desired posi-

tion (see Section 2).

6.

Check hardware for tightness.

7.

Check engine oil level (see Engine

Owner’s Manual).

8.

Check the air filter (see Engine Owner’s

Manual).

9.

Adjust the tilling depth as follows:

A

B

C

Figure 3

a.Loosen tilling depth adjustment knob (A, Figure 3).

b.Move wheel bracket (B, Figure 3) up in relation to height adjustment bar

(C). Moving bracket upward results in shallower tilling, which is recom- mended for initial use.

IMPORTANT: Do not move the wheel bracket any higher than the top of the adjustment bar.

c.Retighten depth adjustment knob.

gasoline or oil/gas mix. The engine must be stopped and cool before adding fuel.

Fill the fuel tank with unleaded gasoline (with a pump octane rating of 86 or higher) according to the directions in the separate Engine Owner’s Manual. The engine is a vertical type, GX 31 model.

STOPPING AND

STARTING THE ENGINE

Stopping the Engine

To stop the engine, move the On/Off Switch (A, Figure 2) to the OFF position.

NOTE: The On/Off switch wire must be securely connected at both ends. Check regularly to ensure that the switch wire is securely connected to the switch and the engine.

Starting the Engine

NOTE: Do not squeeze Engine Throttle/Tines Control Lever (G, Figure 2) when starting engine.

1.Move On/Off Switch (A, Figure 2) to ON position.

WARNING

Do not squeeze the Throttle/Tines Con- trol Lever while starting engine.

Tines may propel the machine forward if the engine speed is advanced from idle. Failure to comply can result in personal injury or property damage.

2.To start a cold engine, move the choke lever (C, Figure 5) to the CLOSED position. To restart a warm engine, leave the choke lever in the OPEN position.

3.To start a cold engine, or after refueling an engine that has run out of fuel, press the priming bulb (A, Figure 4) repeatedly until fuel can be seen in the clear-plastic fuel-return tube (B). To restart a warm engine, it is not necessary to press the priming bulb.

4.Stand in the starting position (Figure 6), keeping your feet positioned safely away from the tines.

5.Place one hand on the upper handlebar to stabilize the machine. Use the other hand to pull the recoil start rope lightly until you feel resistance, then pull briskly. Let the rope rewind slowly after each pull.

NOTE: An alternate stabiliza- tion method is to stand in the starting position (Figure 6), but place one hand on the carrying handle while pulling the starter rope with the

other hand.

6.If the choke lever

was moved to the

 

CLOSED position to

 

start the engine, grad-

 

ually move it to the

 

OPEN position as the

 

engine warms up.

Figure 6

 

Image 7
Contents Tiller/Edger See Back Cover for Customer Service information Operation SafetyTraining PreparationNever perform maintenance when MAINTENANCE/STORAGEKeep children and pets away Unpacking Instructions AssemblyAssembly Steps IntroductionKnow Your Equipment Features and ControlsEngine Controls Stopping Starting the Engine Disconnect the spark plug wireOperation PRE-START PreparationTilling Patterns Adjusting Tine PositionsTilling and Cultivating CultivatingLawn Aerator Attachment Model Installing the Edger AttachmentUsing the Edger Attachment Power Lawn Rake Attachment ModelOther Lubrication Points MaintenanceEquipment Maintenance Transmission MaintenanceAvoid contact with the cutting edges on the tines Engine MaintenanceTine Removal Installation Arranging Tines for Stony SoilOff-Season Storage TroubleshootingStorage Replacing Worn Tine SectionsRef. # Description Parts ListSee Previous Safety and Operating Decals Owner Registration Card Warranty ServiceReplacement Parts Engine Service and Repair