138310-1

MT 600

M I C R O T E C H S E R I E S

Architectural & Engineering Speciﬁcations

Micro-Tech 600 (120 V, 60 Hz models)

The Crown® Micro-Tech 500 power ampliﬁer shall be a solid-state two- channel model employing multi-mode (AB+B) grounded bridge(TM) output circuitry.

The outputs shall be switchable as stereo, bridged-mono or parallel-mono modes of operation. The bridged-mono mode shall bridge the outputs to provide increased output voltage. The parallel-mono mode shall parallel the outputs to provide increased output current.

The output impedance of each channel shall be less than 10 milliohms in series with less than 2 microhenries in stereo mode.

The ampliﬁer shall contain protection circuitry which limits the drive level placed on the output devices before their SOA (Safe Operating Area) is exceeded. This protection circuitry shall calculate the instantaneous volt- age across and current through the output devices while factoring in their simulated junction temperatures to predict how close they are to their operating limits. This protection will be called “ODEP.”

The ampliﬁer shall contain controlled slew-rate voltage circuitry to protect it against radio frequency interference burnouts. It shall also be protected from current overload at its output stage. The slew rate of the ampliﬁer shall be greater than 13 volts per microsecond in stereo mode.

The ampliﬁer shall temporarily go into a stand-by mode if its power trans- former becomes excessively hot and shall automatically resume normal operation once it has cooled to a safe operating temperature.

Front-panel controls shall include an enable on/off switch.

Rear-mounted controls shall include a ground lift switch to isolate the signal ground from the chassis ground, a switch which selects between stereo, bridged-mono and parallel-mono modes of operation, a gain control for each channel, and two push-button reset switches to reset the circuit breakers for the high-voltage power supplies.

Internal controls shall include an input sensitivity switch to select between 0.775 V, 1.4 V or a ﬁxed voltage gain of 26 dB for full rated output.

Front panel indicators shall include an amber power enable indicator and an amber protection system indicator (ODEP) for each channel which shall normally be illuminated to conﬁrm the availability of reserve thermody- namic energy and which shall dim in proportion to limiting when the power demands of the output stages have been exceeded.

The power ampliﬁer shall meet or exceed the following performance criteria. Input sensitivity for rated output: 26 dB voltage gain (unbalanced). Rated FTC output in stereo mode with less than 0.1% THD: 285 watts per channel (20 Hz to 20 kHz) into 4 ohms; 210 watts per channel (20 Hz to 20 kHz) into 8 ohms. Rated FTC output in bridged-mono mode with less than 0.1% THD: 670 watts (20 Hz to 20 kHz) into 8 ohms; 420 watts (20 Hz to 20 kHz) into 16 ohms. Hum and noise: at least 105 dB (A weighted) below full rated output power. Phase response: 10 degrees from 10 Hz to 20 kHz at 1 watt. Frequency response: 20 Hz to 20 kHz, 0.1 dB at 1 watt into 8 ohms per channel in stereo mode. Damping factor: greater than 1000 from 10 to 400 Hz into 8 ohms. Intermodulation distortion (SMPTE): less than 0.05% from 163 milliwatts to rated power into 8 ohms in stereo mode. Harmonic distortion at rated power into 8 ohms per channel (stereo mode): less than 0.05% from 20 Hz to 1 kHz and increasing linearly to less than 0.1% at 20 kHz.

The ampliﬁer shall be safe when driving any kind of load—even highly reactive ones.

The power requirements shall be 120 VAC at 60 Hz. At idle, the ampliﬁer shall draw 100 watts or less.

The ampliﬁer chassis shall be constructed of steel with a durable black ﬁnish and shall be designed for ﬂow-through fan-assisted ventilation from the front panel to the side panels. The ampliﬁer shall have an aluminum front panel with Lexan overlay and air ﬁlter media.

The dimensions of the ampliﬁer shall allow for 19 inch (48.3 cm) EIA stan- dard (RS-310-B) rack mounting. The ampliﬁer shall be 3.5 inches (8.9 cm) tall and 16 inches (40.6 cm) deep behind the rack-mounting surface.

The ampliﬁer shall weigh 36 pounds, 4 ounces (16.5 kg) and shall have a center of gravity approximately 6 inches (15.2 cm) behind the front panel.

The ampliﬁer shall be designated the Crown Micro-Tech 600.

Crown International 1718 W. Mishawaka Rd. Elkhart, IN 46517-9439 TEL: 574-294-8200 FAX: 574-294-8FAX www.crownaudio.com

Speciﬁcations subject to change without prior notice. Latest information available at www.crownaudio.com.

Crown and Crown Audio are registered trademarks of Crown International, Inc. Printed in U.S.A.

04/05

MT 600 specifications

The Crown Audio MT 600 is renowned in the audio industry for its exceptional quality and reliability, making it a favored choice among sound engineers and audio professionals. This power amplifier is designed to deliver high-performance audio solutions across a variety of applications, from live sound reinforcement to installation in fixed venues.

One of the key features of the MT 600 is its robust design, ensuring reliability in demanding environments. The amplifier is built with a strong metal chassis that provides durability and protection against physical impacts. The MT 600 utilizes a switching power supply, which enhances efficiency and reduces weight compared to traditional transformer-based designs. This results in a more portable amplifier without sacrificing power output.

In terms of power delivery, the Crown MT 600 is capable of producing impressive output levels, offering 600 watts per channel at 4 ohms. This substantial power allows it to drive a wide range of speakers effectively, catering to both professional applications and larger venues. The amplifier's frequency response spans from 20 Hz to 20 kHz, ensuring it can faithfully reproduce the full range of audio frequencies for a rich and immersive listening experience.

The MT 600 incorporates advanced technology to protect both the amplifier and connected speakers. It features built-in protection circuitry that prevents overheating and output shorts, ensuring long-term reliability and performance. Additionally, the amplifier has a rear-panel adjustable output level control, allowing users to tailor the audio output to their specific requirements.

Another important characteristic of the Crown Audio MT 600 is its versatility. It is equipped with multiple input options, including balanced XLR and unbalanced 1/4-inch inputs, which make it compatible with a wide range of audio sources. This flexibility allows sound engineers to easily integrate the MT 600 into various setups without the need for additional adapters.

Overall, the Crown Audio MT 600 is a powerhouse amplifier that combines durability, high output capabilities, advanced protection features, and connectivity options. This makes it ideal for live performances, events, and installations where professional-grade audio quality is essential. Its commitment to excellence in sound reproduction and reliability continues to solidify its status as a go-to solution in the audio industry.