Bolens 12226 owner manual Troubleshooting, Problem Possible Cause Correction

Page 23

Section 5: Maintenance 23

TROUBLESHOOTING

Before performing any troubleshooting procedures, refer to the appropriate safety, operating or maintenance instructions in this Manual or in the Engine Owner’s Manual. Contact your local authorized engine service dealer for engine service. Contact your local authorized tiller dealer or the factory for all other service problems.

PROBLEM

 

POSSIBLE CAUSE

 

CORRECTION

 

 

 

 

 

 

 

Engine does

1.

Spark plug wire disconnected.

1.

Reconnect wire.

not start.

2.

Engine Throttle Control Lever incorrectly set.

2.

Put lever in START position.

 

3.

Fuel tank empty.

3.

Add fuel.

 

4.

Choke control (if so equipped) in incorrect position.

4.

See Engine Owner’s Manual.

 

5.

Stale gasoline.

5.

Drain fuel and add fresh fuel.

 

6.

Dirty air filter(s).

6.

Clean or replace filter(s).

 

7.

Defective or incorrectly gapped spark plug.

7.

Inspect spark plug.

 

8.

Carburetor out of adjustment.

8.

See Engine Service Dealer.

 

9.

Misadjusted throttle control.

9.

See Engine Service Dealer

 

10.

Dirt or water in fuel tank.

10.

See Engine Service Dealer.

 

 

 

 

 

Engine runs poorly.

1.

Defective or incorrectly gapped spark plug.

1.

Inspect spark plug (see Engine Owner’s Manual).

 

2.

Dirty air filter(s).

2.

Clean or replace (see Engine Owner’s Manual).

 

3.

Carburetor out of adjustment.

3.

See Engine Service Dealer.

 

4.

Stale gasoline.

4.

Replace with fresh gasoline.

 

5.

Dirt or water in fuel tank.

5.

See Engine Service Dealer.

 

6.

Engine cooling system clogged.

6.

Clean air cooling system (see Engine Owner’s Manual).

 

 

 

 

 

Engine overheats.

1.

Engine cooling system clogged.

1.

Clean air cooling area (see Engine Owner’s Manual).

 

2.

Carburetor out of adjustment.

2.

See Engine Service Dealer.

 

3.

Oil level is low.

3.

Check oil level (see Engine Owner’s Manual).

 

 

 

Engine does not

Misadjusted/faulty engine switch.

See Engine Owner’s Manual or Engine Service Dealer.

shut off.

 

 

 

 

 

 

 

 

 

Wheels and Tines

1.

Improper use of controls.

1.

Review Sections 3 and 4.

will not turn.

2.

Forward Clutch: Misadjusted forward clutch control cable.

2. Adjust cable tension (Section 5).

 

3.

Worn or broken clutch belt(s).

3.

Check belts. Replace parts as needed (Section 5).

 

4.

Internal transmission wear or damage.

4.

Contact local dealer or Factory.

 

5.

Screw and key loose in transmission pulley.

5.

Tighten screw; check that key is in place.

 

 

 

 

 

Tines turn, but

1.

Wheel mounting hardware missing.

1.

Replace hardware.

wheels don’t.

2.

Screw and key loose in transmission pulley.

2.

Tighten screw; check that key is in place.

 

3.

Internal transmission wear or damage.

3.

Contact local Dealer or Factory.

 

4.

Misadjusted wheel gear cable.

4. See Wheel Gear Cable Adjustment, Section 5.

 

5.

Wheel Gear Lever not fully engaged.

5.

Engage lever (see Section 3).

 

 

 

 

 

Wheels Turn, but

1.

Tine holder mounting hardware missing.

1.

Replace hardware.

Tines Don’t.

2.

Internal transmission wear or damage.

2.

Contact local Dealer or Factory.

 

 

 

 

 

Poor tilling

1.

Worn tines.

1.

See Bolo Tines (Section 5).

performance.

2.

Improper Depth Regulator setting.

2.

See Tilling Tips & Techniques, Section 4.

 

3.

Incorrect throttle setting.

3.

See Section 4.

 

4.

Belt(s) slipping.

4.

See Checking Clutch Belt Tension, Section 5.

 

 

 

 

 

Image 23
Contents HP Pony PRO Table of Contents Exercise caution to avoid slipping or falling TrainingPreparation OperationUse slower engine speeds Maintenance and StorageTo Avoid Serious Injury DecalsAttach Handlebars Hardware BAG Parts ListIntroduction Inspect UnitAttach Forward Clutch Control Cable Tighten the two jam nuts securely when tension is correctCable Adjuster Jam Nuts Attach Wheel Gear Lever Check AIR Pressure in TiresADD Motor OIL to Engine Depth Regulator Lever IntroductionWheel Gear Lever Forward Clutch Control LeversRetighten the two screws at the ends of the handlebar To Adjust the Handlebar HeightEngine Controls Starting the Engine PRE-START ChecklistBREAK-IN Operation STARTING/STOPPING EngineStopping the Tiller and Engine Do not till when reversingOperating the Tiller Stopping the EngineLengthwise and then crosswise Tiller along while the tines doYour freshly tilled or cultivated soil Unwanted weed seeds back into Till Freshly tilled groundTerrace Gardening Read the following recommendations before tilling on slopesTilling Up and Down Slopes Vertical Tilling Loading and Unloading the Tiller Clearing the TinesMaintenance Schedule Engine Cleaning CARBURETOR/GOVERNOR Control Adjustments Engine OIL ServiceAIR Cleaner Service Spark Plug ServiceBolo Tines OFF Season StorageChecking and Adjusting Tension on Clutch Belts Checking and Adjusting Forward Clutch Belt TensionRemoving Forward Clutch Belt Installing Forward Clutch Belt19 Correct forward clutch cable position ROW Marker HILLER/FURROWERProblem Possible Cause Correction TroubleshootingDrawing no Part Description Parts List Drawing no1918343 Tine Hood Incl. hood flap 9621 Oil Seal 9511 Parts List Part Description End play on drive shaft Main Drive Shaft AssemblyInput Pinion Shaft & Gear Assembly 1733398 1904522001 See Detail aBumper Row Marker Attachment option9621 Page Owner Registration Card Warranty ServiceReplacement Parts Engine Service and Repair

12226 specifications

The Bolens 12226 is a powerful and versatile two-stage snowblower designed to tackle heavy snowfall and icy conditions with ease. It stands out in the market for its robust construction and innovative technologies, making it an essential tool for homeowners living in regions prone to harsh winter weather.

At the heart of the Bolens 12226 is its reliable 208cc PowerMore engine, engineered for maximum performance and durability. The engine's 4-cycle design ensures efficient fuel use while providing ample torque to handle the toughest of snow. This snowblower features a 26-inch clearing width, allowing it to clear large swathes of snow in a single pass, significantly reducing the time spent on snow removal.

One of the standout characteristics of the Bolens 12226 is its two-stage snow clearing system. In the first stage, the auger collects snow and ice, which is then propelled into the second stage, where an impeller throws the snow out of the chute. This efficient design is ideal for tackling heavy, compacted snow and can easily handle drifts and deeper accumulations.

The snowblower's adjustable chute can rotate up to 200 degrees, allowing the user to direct the snow exactly where they want it to go. The built-in deflector provides further customization, enabling operators to control the height of the discharge, whether they’re clearing a driveway or a sidewalk. This flexibility ensures that users can adapt to various snow conditions and landscapes.

For ease of operation, the Bolens 12226 includes a self-propelled feature with six forward speeds and two reverse speeds, offering comfortable maneuverability across diverse terrains. The large, deep-tread tires enhance traction, providing stability and control even on icy surfaces.

Safety and convenience are key features as well; the snowblower comes equipped with an electric start for hassle-free ignition, eliminating the need for strenuous pull starts in cold weather. Additionally, the ergonomic control panel allows for easy operation, ensuring that users have a comfortable experience while tackling winter challenges.

In summary, the Bolens 12226 is a well-engineered snowblower that merges power and ease of use. With its robust engine, efficient two-stage clearing system, adjustable chute, and user-friendly features, it is an invaluable tool for anyone needing to maintain a clear and safe outdoor space during snowy months. Its thoughtful design and reliable performance make it a standout choice for winter weather preparedness.