Craftsman 917.295651 manual SERVmCE, To Adjust Carburetor See Fig, To Adjust Thronle Control Cable

Page 18

SERVmCE AND

ENGINE

TO ADJUST THRO'N'LE CONTROL CABLE

(See Fig, 27)

o Loosen cable clamp screw to allow cable to move_

oMove throttle control lever on upper'handle to "FAST" position,,

o Pull throttle cable out to end of travel

,Hold cable in this position and tighten clamp screw securely.,

THROTTLE

CABLE

CLAMP SCREW

FIG. 27

TO ADJUST CARBURETOR (See Fig. 28)

The carburetor has a high speed jet and has been preset at the factory and adjustment should not be necessary. How- ever, minor adjustments may be required to compensate for differences in fuel, temperature, altitude or load_ If the carburetor does need adjustment, proceed as follows.

In general, turning the idle needle valve in (clockwise) decreases the supply of fuel to the engine giving a leaner fuel!air mixture. Turning the needle valve out (counter-

clockwise) increases the supply of fuel to the engine giving a richer fuel/air mixture.

IMPORTANT: DAMAGE TO THE NEEDLES AND THE

SEATS IN CARBURETOR MAY RESULT IF SCREWS ARE TURNED IN TOO TIGHT.

PRELIMINARY SETTING

,Air cleaner assembly must be assembled to the carbu- retor when making carburetor adjustments.

•Be sure the throttle control cable is adjusted properly (see above).

', With engine off, turn idle needle valve in (clockwise) closing it finger'tight and then turn valve out (counter- clockwise) 1-1/2 turns_

,,H

!=l= ==

ADJUSTMENTS

FINAL SETTING

-Start engine and allow to warm for five minutes_ Make final adjustments with engine running at idle and drive control bar in "DISENGAGED" position.

=With throttle control lever in "SLOW" position, turn idle needle valve in (clockwise) until engine begins to die then turn out (counterclockwise) until engine runs rough. Turn valve to a point midway between those two positions.

IDLE RPM ADJUSTMENT

- To adjust idle RPM, rotate throttle linkage counter- clockwise and hold against stop while adjusting idle speed adjusting screw to obtain 1750 RPM.. Release throttle linkage.

ACCELERATION TEST

=Move throttle control lever from "SLOW" to "FAST" position. If engine hesitates or'dies, turn needle valve out (counterclockwise) 1/8 turn Repeat test and continue to adjust, if necessary, until engine acceler- ates smoothly..

High speed stop is factory adjusted. Do not adjust or damage may result..

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED OVERSPEEDINGTHEENGINEABOVE THE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED

HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR

NEAREST AUTHORIZED SERVICE CENTER/ DEPARTMENT, WHICH HAS THE PROPER EQUIPMENT

AND EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS.

THROTTLELINKAGE

IDLE SPEED

ADJUSTING SCREW

\

IDLE NEEDLE VALVE

FIG. 28

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Inch TmNEWnDTH Tn Ller with Counter Rotating TinesMaintenance and Storage PreparationOperation Customer Responsibilities Product SpecificationsMaintenance Agreement RJ19LM STD361458Table of Contents Belt Spark Plug Muffler AIR FilterEngine OIL Stabilizer Shear PINTools Required for Assembly Contents of Hardware PackInstall Handle See Figs , 4, Unpacking Carton See FigView from R,H, Side of Tiller Insert Cable Clip See Fig Connect Shift RO D See FigRemove Tiller from Crate Check Tire PressureMeets Ansi Safety Requirements OPERATmONKnow Your Tiller Forward -WHEELS ONLY/TINES Stopped HOW to USE Your TallerTine Operation with Wheel Drive Reverse Wheels ONLY/TINES StoppedOuter Side Shields See Fig Before Starting EngineTurning To TransportTine Shear Pins To Start Engine See FigTilling Hints Lubrication Customer RESPONSmGeneral Recommendations AS YOU Complete ErvicedatesAIR Filter See Fig EngineCooling System See Fig Hoursof operation or every season, whichever occurs firstTiller CleaningBaLUTmES Spark PlugGround Drive Belt Adjustment See To Remove Belt Guard See FigTo Replace Ground Drive Belt See Figs Tine Replacement See Figs , 25 Preliminary Setting To Adjust Carburetor See FigTo Adjust Thronle Control Cable SERVmCEFuel System TillerOther Engine OILTrou Leshooting Pounts

917.295651 specifications

The Craftsman 917.295651 is an impressive lawn tractor designed to provide exceptional performance and efficiency for both residential and light commercial use. This robust machine offers a combination of advanced technologies and practical features, making it an ideal choice for homeowners looking to maintain their lawns with ease.

One of the standout features of the Craftsman 917.295651 is its powerful 19.5 HP Briggs & Stratton engine. This reliable engine delivers ample power to tackle various lawn care tasks, from mowing to mulching and even towing light attachments. The engine is designed for longevity, ensuring that users can depend on it season after season.

Another significant aspect of the 917.295651 is its 42-inch cutting deck, which facilitates efficient mowing by covering more ground in less time. The cutting deck comes equipped with adjustable blade heights, ranging from 1.5 to 4 inches, allowing users to customize their mowing experience according to the specific needs of their lawn. The deck's design promotes an even cut, resulting in a well-manicured lawn.

The inclusion of a hydrostatic transmission system sets this lawn tractor apart from its competitors. This technology allows for smooth and effortless speed adjustments while driving. Users can easily shift from forward to reverse without the need for manual gear changes, providing greater control and a more comfortable riding experience.

Comfort is also a priority in the Craftsman 917.295651, as it features a supportive, high-back seat that helps reduce fatigue during extended periods of use. The ergonomically designed steering wheel ensures that operators can maneuver the tractor with ease, enhancing overall user satisfaction.

Additional characteristics of the 917.295651 include a twin-blade cutting system that ensures a clean and precise cut every time, as well as a hidden fuel tank that adds to its sleek appearance. The tractor's durable construction ensures it can withstand the rigors of regular use, while its compact size makes storage simple.

In summary, the Craftsman 917.295651 lawn tractor is a well-rounded machine that effectively combines power, comfort, and efficiency. Its standout features such as the Briggs & Stratton engine, hydrostatic transmission, and adjustable cutting deck make it a versatile choice for maintaining any lawn. Whether homeowners are mowing their yard or tackling larger properties, this tractor is designed to make lawn care tasks easier and more enjoyable.
Top Page Image Contents