Husqvarna 650CRT owner manual Storage, Other, Fuel System, Engine OIL, Cylinders

Page 18

STORAGE

Immediately prepare your tiller for storage at the end of the season or if the unit will not be used for 30 days or more.

CAUTION: Never store the tiller with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TILLER

Clean entire tiller (See “CLEANING”in the Maintenance section of this manual).

Inspect and replace belts, if necessary (See belt re- placement instructions in the Service and Adjustments section of this manual).

Lubricate as shown in the Maintenance section of this manual.

Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

FUEL SYSTEM

IMPORTANT:IT IS IMPORTANTTO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS THE CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTUREWHICH LEADSTO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.

Drain the fuel tank.

Start the engine and let it run until the fuel lines and carburetor are empty.

Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in mini- mizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER(S)

Remove spark plug.

Pour 1 ounce (29 ml) of oil through spark plug hole into cylinder.

Pull starter handle slowly several times to distribute oil.

Replace with new spark plug.

OTHER

Do not store gasoline from one season to an- other.

Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

If possible, store your unit indoors and cover it to give protection from dust and dirt.

Cover your unit with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your unit to rust.

IMPORTANT: NEVER COVER TILLER WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.

18

Image 18
Contents 650CRT Training Safety RulesMaintenance and Storage PreparationTable of Contents Assembly Tools Required for AssemblyOPERATOR’S Position See Fig Install Handle See Figs , 4, Unpacking Carton See FigRemove Tiller from Crate Attach Clutch Cable See FigConnect Shift ROD See Fig Check Tire PressureMeets Ansi Safety Requirements OperationKnow Your Tiller Forward Wheels ONLY/TINES Stopped HOW to USE Your TillerTine Operation with Wheel Drive Reverse Wheels ONLY/TINES StoppedTo Transport Before Starting EngineTurning ADD GasolineTine Shear Pins Tilling HintsCultivating Lubrication Chart MaintenanceMaintenance Schedule General RecommendationsEngine AIR Filter See FigSpark Plug CleaningMuffler Cooling System See FigService and Adjustments TillerTire Care Ground Drive Belt Adjustment See Fig To Replace Ground Drive Belt See FigTine Replacement See Figs , 25, To Adjust Throttle Control Cable See Fig To Adjust CarburetorFuel System StorageOther Engine OILTroubleshooting Points Handle Assembly Tiller - Model Number 650CRTC, Product Number 954 32MAINFRAME, Left Side MAINFRAME, Right Side Cludes Key No Tine Shield KEY Part DescriptionTine Assembly Decals Warranty Statement 532 18 48-25 Rev 05.13.03 TR